Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for MMD Equipment PowerPro IGR6000H
Summary of Contents for MMD Equipment PowerPro IGR6000H
- Page 1 PowerPro Inverter Generators Owners Manual IGR6000H MMD Equipment 4175 Guardian Street • Simi Valley, CA 93063 602 Dunton St. • San Antonio, TX 78226 2075 High Hill Road • Logan Township, NJ 08085 Phone: 800-433-1382 www.mmdequipment.com Fax: 800-225-5579...
-
Page 2: Table Of Contents
If a problem should arise, or if you have any questions about the generator, consult an authorized sales Scan for MMD representative, or MMD Equipment at: technical support mmdequipment.com/tech-support.html Page 2 MMD PowerPro Inverter Generators • IGR6000H (091615) MMD PowerPro Inverter Generators •... -
Page 3: Safety Instructions
1. Safety Instructions Failure to properly follow these precautions This generator is designed to provide safe and dependable service if operated according to can result in property damage, serious injury or instructions. DEATH! Read all labels and the owner's manual before n Read and understand the Owner’s Manual before operating this generator. -
Page 4: Component Locations
2. Component Locations Read the labels and safety notes and precautions on the generator. Connections for standby power to a building's electrical system must be made by a qualified electrician and must If a label comes off or becomes hard to read, contact your sales representative for a comply with all applicable laws and electrical codes. - Page 5 Control Panel — IGR6000H Serial Number Identification and Location OVERLOAD PROTECTOR The engine serial number is stamped on the engine block to the left of the oil drain SMART HOUR METER plug. In most cases the battery will have to be removed to view it clearly. Refer to THROTTLE AC RECEPTACLES this number when ordering parts or making technical inquiries.
-
Page 6: Pre-Operation Check
3. Pre-Operation Check Be sure to check the generator on a level surface with the Using non detergent oil or 2 cycle engine oil could shorten the engine’s service life. engine stopped. Under no circumstances can this generator be used in an enclosed compartment. n Use a high-detergent, Running the engine with insufficient oil can cause premium quality 4-stroke... - Page 7 3. Check the air cleaner. a. Check the air cleaner element to be sure it is clean and in good condition. n Gasoline is extremely flammable and is explosive under certain conditions. b. Open the left side maintenance cover. n Refuel in a well-ventilated area with the engine stopped. Keep all possible c.
-
Page 8: Starting The Engine
4. Starting The Engine Disconnect any load from AC receptacle before starting engine. c. Insert the engine key and turn the engine switch to ON position. n When starting the generator after adding fuel for the first time or after long term storage, or after running out of fuel, turn the fuel valve lever to the "ON"... -
Page 9: Generator Use
5. Generator Use e. Push the choke knob in to the OPEN position as the engine warms up. Warnings and cautions n To prevent electrical shock from faulty appliances, the generator should be grounded. Connect a length of heavy cable between the generator's ground terminal and an external ground source. - Page 10 n 14 Gauge Cords- a 14 gauge cord between 0-50 feet (0-15.2 meters) long will adequately handle loads between 10 and 15 amps. n Do not attempt to operate appliances if the ground fault circuit interrupter reset button pops out repeatedly during use. n 12 Gauge Cords- If your load is between 10 and 15 amps and the length of the cord is 50-100 feet (15.2-30.5 meters), you need a 12 gauge cord to safely power n Only the ground fault circuit interrupter receptacle provides ground fault...
- Page 11 Output and Overload Indicators DC Operation The output indicator light (green) will remain on during The DC receptacle may be used for charging 12 volt automotive-type batteries only. normal operating conditions. It is not designed to operate DC motors or transformers. Output voltage is 15-30V. DC output will vary according to the position of the Smart-throttle switch.
- Page 12 2. Start the engine Low oil alarm system The low oil alarm system is designed to prevent engine damage caused by an insufficient amount of oil in n The DC receptacle may be used while the AC power is in use. the crankcase.
- Page 13 SMART Throttle High altitude operation When the SMART throttle is placed in At high altitude, the standard carburetor air-fuel mixture will be excessively rich. the on position, engine speed is kept at Performance will decrease, and fuel consumption will increase. idle automatically when the electrical High altitude performance can be improved by installing a smaller diameter main load is disconnected and returns to the...
-
Page 14: Stopping The Engine
6. Stopping The Engine 7. Maintenance To stop the engine in an emergency, turn the engine switch to the OFF position. Perform maintenance and adjustment to keep the generator in the best operating condition. Inspect or service as scheduled in the table below. IN NORMAL USE: n Shut off generator before performing any maintenance. -
Page 15: Maintenance
The use of replacement parts or Spark Arrester Clean accessories which are not designed by MMD Equipment may affect the engine Fuel Sediment Clean emission performance. The manufacturers of replacement parts and accessories... - Page 16 n Make sure to turn the engine switch and the fuel cap vent lever OFF before n Please dispose of used motor oil in a manner that is compliant with environment draining oil. and local disposal regulations. Do not throw it in the trash, pour it on the ground, or down the drain.
- Page 17 3. SPARK PLUG MAINTENANCE To ensure proper engine operation, the spark plug must be properly gapped and free n The spark plug must be securely tightened. An improperly tightened plug can of deposits. become very hot and possibly damage the generator. Recommended spark plug: WR7DC n Never use a spark plug with an improper heat range.
-
Page 18: Transporting And Storage
8. Transporting and Storage To prevent fuel spillage when transporting or during temporary storage, the generator 4. Spark plug and engine should be secured in its normal upright operating position with the engine switched a. Remove the spark plug and pour about a tablespoon of clean engine oil into the OFF. -
Page 19: Wheel Kit
9. Wheel Kit 10. Troubleshooting To install the front wheels, install a Engine will not start washer on the axle, then the wheel, Problem/Possible cause Corrective action another washer and secure with a wheel No fuel in tank Refuel with gasoline clip. -
Page 20: Specifications
32.25 x 19.5 x 23.5 THAN DEFECTS IN MATERIAL OR WORKMANSHIP OF parts will be covered by MMD Equipment for any failure that THE PRODUCT. THIS WARRANTY DOES NOT EXTEND is proven to be a failure in material or workmanship under Dry Weight, lb. -
Page 21: Emission Control System
MMD Equipment. Equipment recommends that you retain all record/receipts covering maintenance on your engine, but MMD Equipment cannot deny warranty claims based on a lack of receipts or for your failure to Owner’s Warranty Responsibilities perform all scheduled maintenance. - Page 22 Inlet system AIR FILTER SHELL Carbon canister location FIXED BRACKET SEAL GASKET FILTER ELEMENT AIR FILTER COVER Bracket Curved hose Carbon canister CARBURETOR Vent hose Fuel system Fuel cap Fuel Tank Cover Threaded sleeve Pallet Cotter Bushing Filter screen Washer Exhaust system SECONDARY AIR Gasket...
- Page 23 Notes Warranty Registration Please complete this page and FAX to: 210-923-3489 Or mail a copy to: MMD Equipment 602 Dunton Street San Antonio, TX 78226 Attn: Product Registration Retail Purchase Date _________________________________________ Model Number ______________________________________________ Serial Number ______________________________________________ Sales Representative _________________________________________...
- Page 24 Notes Notes Page 46 MMD PowerPro Inverter Generators • IGR6000H (091615)
- Page 25 Scan for MMD technical support MMD Equipment 4175 Guardian Street • Simi Valley, CA 93063 602 Dunton St. • San Antonio, TX 78226 2075 High Hill Road • Logan Township, NJ 08085 Phone: 800-433-1382 www.mmdequipment.com Fax: 800-225-5579...
Need help?
Do you have a question about the PowerPro IGR6000H and is the answer not in the manual?
Questions and answers