Page 1
Full HD Camera Operation Manual VER 2.1.18-B2143 2015/08/14...
Page 2
If you want to get the latest product information, operation manual, firmware, or you have any question to the products of BlueEyes Technology, please contact your local agent or go to the official website of BlueEyes Technology for further information.
2. Safety and precautions ......................6 3. Device Description ......................... 7 3.1 Back Panel ..............................7 3.2 Fixed iCam camera ............................8 3.3 Scanning iCam camera ..........................8 3.4 LED Indicator (Separately Sold) ........................9 3.5 Live Video ..............................11 4.
Page 4
Q6: Ripple shows when using projector or digital board ................. 45 Q7: The video file cut into one or several pieces ..................... 46 Q8: How to restore to default? ........................46 Q9: How to reduce background noise ......................47 BlueEyes Technology www.BlueEyes.tw...
Now we have the third generation iCam. It not only reserves the high quality of shooting, but also upgrades the sound receiver. In order to enhance the characters on the whiteboards, digital boards, and projectors, iCam can detect the external environment automatically and make the characters clearer.
– Please do not disassemble, re-design or maintain the device by yourself. – The processors and accessories all pass the safety test of CE and FCC. Please plug the cables of iCam when thundering to avoid lightning strikes. Lightning strike is natural disaster so it is not in our warranty.
10/100 speeds. VIDEO Connect to video equipment, such as a monitor or projector. LINE IN Connect to an audio input source. Do not test or connect the interface not commonly used. It may cause instability of the system. BlueEyes Technology www.BlueEyes.tw...
– The small monitor can suck on the direction controller. If you worry that it is not steady enough, you can stick directly on the monitor. – There are two control buttons on the direction controller of the scanning iCam camera, and the left and right controller is for SES. If you worry that the students might drop it on the floor, you can stick it in the table with double -sided tape or silicone as some of the education institutes do.
– Use [single tone]for audio cable 3.4 LED Indicator (Separately Sold) LED indicator on iCam shines when recording, or iFollow technology appointed. LED should go with SES lecture recording system. If you use SES Lite, the LED indicator would not work.
※ Diagram ※ Wiring Diagram LED indicator has two cables: G and OUT. Plug the two cables in the corresponding point on the back panel. BlueEyes Technology www.BlueEyes.tw...
Click LiveView to watch the video. The operator username is sesuser. As a default, check the factory configured list. You can edit account name or password in setting. We recommend using Microsoft Internet Explorer version 10 or higher web browser. BlueEyes Technology www.BlueEyes.tw...
– Better install on the wall at the back of the classroom. Viewport of the location of camera If you didn’t install the camera at the location aimed the center of the blackboard, the blackboard would show as a trapezoid BlueEyes Technology www.BlueEyes.tw...
Page 14
Elevation of the location of camera If you install the camera too high, the blackboard would show as a trapezoid, the bottom is shorter than the upper side. BlueEyes Technology www.BlueEyes.tw...
5. Adjusting lenses 5.1 Lens of iCam Please loosen the nuts on the lens before adjusting the lens. But please do not remove it or it may get lost. The adjust order is A. Focus distance (W←→T) B. Focus (∞←→N) C.
– The tips for adjusting is to make the left and right sides of the shooting scene justify both sides of the board, but when using scanner module, make the up and down sides of the shooting scene justify up and down sides of the board. – Fasten the nut after adjusting. BlueEyes Technology www.BlueEyes.tw...
– If you find the lens have dust or fingerprint Please blow the dust away with [lens blower] first Then wipe the lens clockwise from center to the outer with [lens pen] – Do not blow with mouth or wipe with tissue. BlueEyes Technology www.BlueEyes.tw...
Page 19
Do not remove the lens. This may make the lens stained with dust and fingerprint. ╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳━╳ BlueEyes Technology www.BlueEyes.tw...
You can change all video streaming related elements in Video Setting page, this page is separated into two parts as shown below. The upper half is streaming setting and bottom half is camera additional information. All function is explained as below: BlueEyes Technology www.BlueEyes.tw...
Key Functions: Camera Default is iCam. (iCam) Specifies the name of the IP Camera. Stream Type Default is Dual. Specifies the dual streaming method used. Options include: Single and Dual. Default is Dual H.264. Codec Choose the video format from「H.264+JPG」 、 「MPEG+JPEG」 、 「Dual H.
Page 22
Do not edit the default unless you are trained and understand the way and the meanings of editing. We recommend using Microsoft Internet Explorer version 10 or higher web browser. BlueEyes Technology www.BlueEyes.tw...
7.2 Camera Setting BlueEyes Technology www.BlueEyes.tw...
Page 24
Key Functions: Default is iCam Camera Enter the name of IP Camera. Default is 128. Brightness Select the required brightness level that ranges from 1 to 255 . . A brighter scene appears, if you choose higher level of brightness.
Page 25
Default is On Schedule Mode Default is OFF Default is OFF Privacy Blocking a specific area on the monitor for the protection of individual privacy. We recommend using Microsoft Internet Explorer version 10 or higher web browser. BlueEyes Technology www.BlueEyes.tw...
4. Place the rectangle over the area to cancel. You can set privacy masks only for one area while checking the image on the camera and privacy area is displayed in red color. If you want to cancel the area, you can click on the red area. BlueEyes Technology www.BlueEyes.tw...
Page 27
5. You can watch the Live view to check the range of the privacy mask. BlueEyes Technology www.BlueEyes.tw...
Both Mic & Speaker: Enables both audio playback & capture in camera. Default is Line in. Audio Source Then select MIC in or Line In. Default is 0 Input Gain Sets the input capture gain, values set from 1 -100 BlueEyes Technology www.BlueEyes.tw...
Page 29
We recommend using Microsoft Internet Explorer version 10 or higher web browser. BlueEyes Technology www.BlueEyes.tw...
Secondary DNS Server Network of preferred and alternate DNS server address . Camera MAC address Detected MAC Detected MAC address Current MAC Current MAC address We recommend using Microsoft Internet Explorer version 10 or higher web browser. BlueEyes Technology www.BlueEyes.tw...
7.6 Solving Color Cast when rotating When iCam is set on the scanner module, it would rotate to follow the teacher. This kind of shooting may cause color cast. This is because the changes of light would make the White Balance over adjusted.
8. Watermark 8.1 Trademark of education institute Many education institutes want to mark their name on the videos. You can upload the trademark and name on iCam. 8.2 Making Trademark Picture Click +R or [Start] [implement] to open the implement window. Enter the instruction below to open Paint.
Save asBMP pictureFile type【24 bitmap】!Important! 8.3 Upload Watermark Use IE browser to connect to iCam1080 network management. Click [Watermark] in [Maintenance]. Here are the steps: Step 1: Click【Choose file】 to choose your watermark picture. Then click [Open] Step 2: BlueEyes Technology www.BlueEyes.tw...
Page 35
You can choose which corner you want to put the watermark. Please choose the position of the watermark in Watermark【Position】. You should check enable the watermark so the watermark would show on the monitor. We recommend using Microsoft Internet Explorer version 10 or higher web browser. BlueEyes Technology www.BlueEyes.tw...
File name is BMP file 24 bitmap Length and width can be individually divisible by 4 (Pixels) Leave the white blank to avoid color confusion The minimum length and width is 100px Place it on bottom-left BlueEyes Technology www.BlueEyes.tw...
Please type in the website or words you want to show after scanning QRcode. Every time you enter words or websites, you have to click it again. You can check with your cellphone to see if the QRcode is correct. BlueEyes Technology www.BlueEyes.tw...
Page 38
Save the file as BMP File(*.bmp) Or there are many websites to make free QRcode: http://goqr.me/ Select the URL page Enter the website you want for QRcode. Select 【not stored】 Click Download to download QRcode BlueEyes Technology www.BlueEyes.tw...
Page 39
Download as PNG, but it has to be BMP file when uploading. Click +R or [Start] [implement] to open the implement window. Enter the instruction below to open Paint. %systemroot%\system32\mspaint.exe Open the QRcode file in Paint: BlueEyes Technology www.BlueEyes.tw...
Save asBMP pictureFile type【24 bitmap】!Important! 9.3 Upload QR code Use IE browser to connect to iCam1080 network management. Click [Watermark] in [Maintenance]. Here are the steps: Step 1: Click【Choose file】 to choose your QRcode. Then click [Open] BlueEyes Technology www.BlueEyes.tw...
Page 41
It would show like this if it uploads successfully. You can see the QRcode on the live video. Step 4: You can choose which corner you want to put the QRcode. Please choose the position of the watermark in Watermark【Position】. BlueEyes Technology www.BlueEyes.tw...
File name is BMP file 24 bitmap Length and width can be individually divisible by 4 (Pixels) Leave the white blank to avoid color confusion The minimum length and width is 100px Place it on bottom-left BlueEyes Technology www.BlueEyes.tw...
10. Motion detection of iFollow 10.1 Enable and set the motion detection Step1: Open IE browser. Enter camera IP address, account and password. Step 2: Click “Alarm” on the left side of “Setting” Step 3: Click enable “Motion detection” BlueEyes Technology www.BlueEyes.tw...
Page 44
Step 4: Set these red boxes. The red boxes are the motion detection. Click the transparent boxes to make them become red boxes. Click the again to cancel BlueEyes Technology www.BlueEyes.tw...
10.2 Notices If the students come late or leave the seat, motion detection may misjudge teacher’s position. If the board erasers come up to stage when lecturing, motion detection may misjudge teacher’s position.. BlueEyes Technology www.BlueEyes.tw...
Wooden wall or calcium silicate would shake when opening and shutting the door or turning on the air conditioners. 1. It would happen the same thing when installed the iCam on the ceiling T grid. Use telescopic support and install it on the cement ceiling above the ceiling T grid.
Adjust IRIS of iCam lens. Turn the IRIS to O (Open) to make more light come in. Change the exposure mode to indoor, Gain as 0db. If you find that the scene is over-exposure, turn the IRIS to C (Close) to adjust the light amount until the words are clear.
There are many reasons why causes noise. You can ask for professional audio manufacturers for help. There are several ways to solve the problems: 《First way》change electric suppliers Change the power transformer to [voltage transformer]. (As the picture below) Isolating transformer Power strip Stable voltage UPS BlueEyes Technology www.BlueEyes.tw...
Page 49
《Second way》Improve the audio cable Use Hi-Fi audio cable which is better to reduce noise and distortion. 《Third way》Use high-impedance headphone Circumaural headphones is more high-impedance than canalphone. High-impedance headphones can avoid noise but the sound would become smaller. BlueEyes Technology www.BlueEyes.tw...
Need help?
Do you have a question about the iCam and is the answer not in the manual?
Questions and answers