Table of Contents
Related Manuals for Maretron Alarm Module ALM100
Summary of Contents for Maretron Alarm Module ALM100
- Page 1 ® ® ALM100 Alarm Module User’s Manual Revision 1.0 Copyright © 2008 Maretron, LLP All Rights Reserved Maretron, LLP 9014 N. 23 Ave #10 Phoenix, AZ 85021-7850 http://www.maretron.com Maretron Manual Part #: M001901 Revision 1.0 Page i...
-
Page 2: Revision History
ALM100 User's Manual Revision History Revision Description Original document Page ii Revision 1.0... -
Page 3: Table Of Contents
Technical Support ... 9 Installation Template ... 10 Maretron (2 Year) Limited Warranty ... 11 Figure 1 – Mounting the ALM100 into an Electrical Box ... 3 Figure 2 – Flush Mounting the ALM100 Directly to a Wall ... 4 ®... -
Page 5: Introduction
Completely waterproof, the Alarm Module can be mounted inside or outside the vessel. The Maretron ALM100 is designed to operate within the harsh demands of the marine environment. However, no piece of marine electronic equipment can function properly unless installed, configured, and maintained in the correct manner. -
Page 6: Alm100 Accessories
Maretron offers the following accessories for the ALM100: • CP-WH-ALM100 1.4 Quick Install Installing the Maretron ALM100 involves the following five steps. Please refer to the individual sections for additional details. 1. Unpack the box (Section 2.1) 2. Choose a mounting location (Section 2.2) 3. -
Page 7: Mounting The Alm100
® ® 2.3 Mounting the ALM100 The ALM100 is designed to be mounted in an ANSI/NEMA WD 6 electrical switch box, but it may also be mounted directly into a wall. If mounting the ALM100 into an electrical box, which can in turn be surface-mounted onto a wall or bulkhead, attach the ALM100 securely to the electrical box using the included mounting screws or other fasteners as shown in Figure 1 below. -
Page 8: Connecting The Alm100
ALM100 User's Manual ALM100 Faceplate Faceplate Mounting Screws (x2) Sounder Collar Figure 2 – Flush Mounting the ALM100 Directly to a Wall The following instructions apply wither mounting the ALM100 into an electrical box or to a wall: 1) Connect the NMEA 2000 cable to the connector on the ALM100 Alarm Module 2) Using the included ALM100 mounting screws, mount the ALM100 Alarm Module to the wall or electrical box 3) Place the sounder gasket over the sounder on the ALM100 alarm module... -
Page 9: Checking Connections
ALM100 test function on an appropriate NMEA 2000 display, such as the Maretron DSM250. If the alarm does not sound and flash the red LED during testing, please refer to Section 4, “Troubleshooting”. 2.5 Configuring the ALM100 The ALM100 will sound alarms received over the NMEA 2000 network as it is shipped from the factory;... -
Page 10: Device Instance
Maretron N2KView Vessel Monitoring System and the Maretron DSM250 display. The label will let you assign an easy-to-remember text label (example: “Alarm in Pilothouse”) to make it easy for you to identify the device as you are configuring the monitoring software or display, as well as when alerts are generated. -
Page 11: Troubleshooting
4 Troubleshooting If you notice unexpected operation of the Maretron ALM100, follow the troubleshooting procedures in this section to remedy simple problems. If these steps do not solve your problem, please contact Maretron Technical Support (refer to Section 6 for contact information). -
Page 12: Technical Specifications
ALM100 User's Manual 5 Technical Specifications As Maretron is constantly improving its products, all specifications are subject to change without notice. Maretron products are designed to be accurate and reliable; however, they should be used only as aids to navigation and not as a replacement for traditional navigation aids and techniques. -
Page 13: Technical Support
6 Technical Support If you require technical support for Maretron products, you can reach us in any of the following ways: Telephone: World Wide Web: Revision 1.0 1-866-550-9100 Fax: 1-602-861-1777 E-mail: support@maretron.com http://www.maretron.com Mail: Maretron, LLC Attn: Technical Support 9014 N. 23... -
Page 14: Installation Template
ALM100 User's Manual 7 Installation Template Please check the dimensions before using the following diagram as a template for drilling the mounting holes because the printing process may have distorted the dimensions. Figure 4 – Mounting Surface Template Page A10 Appendix A –... -
Page 15: Maretron (2 Year) Limited Warranty
Maretron’s option, of any product not meeting the above limited warranty and which is returned to Maretron; or if Maretron is unable to deliver a replacement that is free from defects in materials or workmanship, Purchaser’s payment for such product will be refunded.