Related Manuals for DAPAudio Dap-6
Summary of Contents for DAPAudio Dap-6
- Page 1 Valid from Serial No.: Dap~6: 3 880305 Dap-7: 4021449 Dap-V: 4042248 Manual No.: 14027001 Instruction Manual (vol. 1 of 4) Date of Release 04.12.1995...
- Page 2 Instruction Manual Safety Precaution Sbeet To be read carefully before use 1. The operator should be fully aware of the use of the machine according to the Instruction Manual. The machine must be placed in an adequate working position. Be sure that the actual voltage corresponds to the voltage stated on the type plate.
- Page 3 Instruction Manual Table of Contents Page User’s Guide ..,..,....,...,,..,,,.,,. Reference Guide Always state Serial No and Voltage/frequency if you have technical questions or when ordering spare parts. You will find the Serial No. and Voltage on the front cover of this manual or on an attached label below, It in doubt consult the rating plate of the machine itself.
-
Page 5: Table Of Contents
Checking the Contents ofPacking Dap-6 Dap-7 and Dap-V Placing Dap Supplying Power Supplying Water Water Inlet Water Outlet 2. Operation Getting Acquainted with Dap-6/-7/-V Mounting the Disc Starting the Machine Dap-6 Dap-7 Dap-V Stopping the Machine Dap-6, Dap-V Dap-7 Overload... -
Page 6: Getting Started
Instruction Manual 1. Getting Started Checking the Contents of In the packing box you should find the following parts: Packing Dap-6, complete with inlet hose and cable Dap-6 Splash ring, 0210 mm Splash ring, 0240 mm Outlet hose Elbow pipe... -
Page 7: Placing Dap
Instruction Manual Getting Acquainted with Take a moment to familiarize yourself with the location and Dap-6/-7/-V names ofthe Dap components. Dap-6 Day-V Day-i D Speed Selector ~D ON/OFF Switch ON/OFF switch ‘2~ Thermal Cut-out © Thermal Cut-out © Speed Selector ‘3~ Turntable... -
Page 8: Supplying Water
Dap-6 is not delivered with a water tap. An optional water tap (DAPTA) is available, see section Accessories. -
Page 9: Mounting The Disc
The speed indicator shows the actual speed ofdisc. Stopping the Machine Press the ON/OFF switch. The machine stops operating. Dap-6, Dap-V Set the adjusting knob to zero. The machine stops operating. Dap- 7 Overload A thermal cut-out is mounted in the Dap machines which switches offthe machines in case of overload. - Page 10 Instruction Manual Reterence Guide Table of Contents Page 1. Accessories 2. Trouble-Shooting 3. Maintenance Daily Service Weekly Service Adjusting the Belt 4. Technical Data...
-
Page 11: Accessories
Polishing disc (PVC for adhesive grinding paper and for polishing) o200 mm DEPKI 0250 mm ROTRO Water Tap To be mounted on Dap-6 DAPTA Remember... Struers offers a comprehensive range of consumables for grinding and polishinq. Please ask for separate leaflets. -
Page 12: Trouble-Shooting
Instruction Manual 2. Trouble-Shooting Error Cause Action Outlet hose is blocked Dirt in the tray or outlet hose Clean the tray or outlet hose Transmission inadequate/Disc stops Loose belt. Open Dap according to the description in chapter 3, turning Maintenance, and check the belt: Adjust the belt If the belt is new Replace the belt... -
Page 13: Maintenance
Instruction Manual 3. Maintenance Daily Service Clean all accessible surfaces with a moist cloth. When using embedding resins, aluminium oxide polishing etc., the machine should be thoroughly cleaned as e.g. excess resin or oxide can block the outlet hose. • Remove the disc and clean off the debris from the tray and Weekly Service outlet hose. -
Page 14: Technical Data
For Dap-7/Dap-V: Pedemin-S Specimen Mover Safety Standard IEC 204/ EN 60204-1 (VDE 0113) Noise Level Dap-6: 55 dB (A) Dap-7: 55 dB (A) Dap-V 65 dB (A) Measured at idle running, at a distance of 1.0 m/39.4” from the machine.