Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Certa CTMSESNDRXA
Summary of Contents for Certa CTMSESNDRXA
-
Page 2: General Power Tool Safety Warnings
GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. 1) Work area safety ... -
Page 3: Personal Safety
3) Personal safety Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. - Page 4 Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.
- Page 5 ADDITIONAL SAFETY RULES FOR YOUR MULTI-SANDER Never use your multi-sander for wet sanding with accessories, • also for sawing, scraping, cutting, polishing, and separating. • Always wear eye protection. • Always wear ear protection during extended periods of operation. Always wear a dust mask if the operation is dusty. •...
- Page 6 WARNING! Some dust particles created by power sanding, contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. Crystalline silica from bricks and cement and other masonry products. •...
- Page 7 This symbol is known as the ‘Crossed-out Wheelie Bin Symbol’. When this symbol is marked on a product or battery, it means that it should not be disposed of with your general household waste. Some chemicals contained within electrical/electronic products or batteries can be harmful to health and the environment.
-
Page 8: Specifications
SPECIFICATIONS:... -
Page 9: Technical Data
COMPONENT LIST 1. On/off switch 2. Soft grip handle 3. Dust box cover clamp 4. Dust collection box 5. Hook and loop base plate 6. Sanding paper 7. Motor housing ACCESSORIES Dust collection box 30 x sanding paper (10x80#,10x100#, 10x120#) TECHNICAL DATA Rated voltage 230V~50Hz... - Page 10 WARNING: The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used dependent on the following examples and other variations on how the tool is used: How the tool is used and the materials being sanded.
-
Page 11: Operation Instructions
OPERATION INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. 1) SWITCHING ON AND OFF (See Fig. A1,A2) Fig. Fig. A1 • To switch on, depress the “I” mark on the shank of the on/off switch (1) to the end. To switch off, depress the “O “ mark on the shank of the on/off switch (1) to the end. - Page 12 2) EMPTY DUST BOX (See Fig. C) Fig. C For more efficient operation, please empty the dust box every 15 minutes. This will permit the air to flow through the box more efficiently. To empty the dust box, remove the dust box from sander, then depress both the dust box cover clamps (3) to remove the dust box cover from dust box and shake out dust.
-
Page 13: Selecting The Right Grade Of Sandpaper
CAUTION! Take care to regularly clean out the build up of dust on the base underneath the sanding paper and not to let the sanding paper wear completely down before replacing it. Failure to observe these two precautionary measures can lead to damage to the hook and loop on the base plate and the sanding paper will not attach properly. -
Page 14: Maintenance
5) USING THE SANDER (See Fig. E) Fig. E This sander can be used for most sanding operations on materials such as wood, plastic, metal and painted surfaces. Wear safety goggles, dust mask and ear defenders. Switch the sander on whilst it is resting on the workpiece. Take care to hold the whole area of the base plate on the work. -
Page 15: General Inspection
• Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool. • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. GENERAL INSPECTION Regularly check that all the fixing screws are tight. -
Page 16: Warranty
Warranty The Kogan warranty applies to the original purchaser only; this power tool to be free from defects in material and workmanship. Subject to certain exceptions, Kogan will repair or replace any part on an electric power tool which, after examination, is determined to be defective in material or workmanship for a period of one after the date of purchase unless otherwise noted.
Need help?
Do you have a question about the CTMSESNDRXA and is the answer not in the manual?
Questions and answers