Advertisement
Quick Links
Equipped with Electric Brake
MODEL 6703D
MODEL 6703DW
With Fast Charger
Capacities
Bolt, nut and
machine screw
size
3
mm
~
5
mm
(1/8"
-
3/16")
INSTRUCTION MANUAL
Overall
Net
IRPM)
length
weight
5 kg.cm
-
37 kg.cm
333
mm
1.3 kg
(0.4
ft.lbs
-
2.7
ft.lbsl
(13-118")
(2.9
Ibs)
Fastening torque
No load speed
400
SPEC
IF
I CAT I
0
N S
Battery Cartridge 9100
Voltage
9.6 V
Model DC9700 Fast Charger
Input
output
Charging time
A.C. only 50 Hz
-
6 0 Hz
D.C. 7.2 V, 9.6 V
I
1 Hr.
*
Manufacturer reserves the right to change specifications without notice.
Note: Specifications may differ from country t o country.
WARNING: For your personal safety, READ and UNDERSTAND before using
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Advertisement
Related Manuals for Makita 6703D
Summary of Contents for Makita 6703D
- Page 1 SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Equipped with Electric Brake Fastening torque IRPM) 5 kg.cm 37 kg.cm (0.4 ft.lbs Input 6 0 Hz D.C. 7.2 V, 9.6 V MODEL 6703D MODEL 6703DW With Fast Charger Overall length weight 1.3 kg (13-118") (2.9 ft.lbsl output Charging time 1 Hr.
-
Page 2: Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw.
- Page 4 VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user as well as damage t o the tool.
- Page 5 Before using battery charger, read all instructions and cautionary markings battery charger, CAUTION To reduce risk of injury, charge only MAKITA Battery Cartridge 9100, 9100A. 9101 81 9101A. Other types of batteries may burst causing personal injury and damage. Do not expose charger t o rain or snow.
- Page 6 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents.
- Page 7 Installing or removing the battery cartridge Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing the tool.
- Page 8 When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely a couple of times.
- Page 9 Switch action To start the tool, simply pull the trigger. Release the trigger to stop. CAUTIO N : Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. Reversing switch action This tool has a reversing switch to change...
- Page 10 Adjusting the fastening torque The fastening torque can be adjusted infi- nitely from approx. 5 kg . cm 37 kg cm (2.7 ft . Ibs). T o adjust loosen the two screws and turn the adjusting ring. Then tighten the screws to secure the adjusting ring.
-
Page 11: Maintenance
Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed Makita replacement parts. Makita Authorized or Factory Service Centers, always using... - Page 12 ACCESSORIES CAUTION: These accessories or attachments are recommended for use w i t h your Makita tool specified in this manual. The use,of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner.
- Page 13 Sep.--29-'94 CORDLESS SCREWDRIVER Model 67031) Note: The switch and other part configurations may differ from country to country.
- Page 14 MODEL 6 7 0 3 D DESCRIPTION Ring Spring 1 1 Flat Washer 12 Compression Spring 13 Sleeve Steel Ball Spindle Key 4 Retaining Ring 5 - 3 4 Flat Washer 3 4 Head Flat Washer Ball Bearing 6000LLB Flat Washer 1 0 Retaining Ring S - 1 0 Screw M 4 x 6 Change Ring...
- Page 15 MAKITA LIMITED ONE YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted t o be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.