Subscribe to Our Youtube Channel
Related Manuals for Prestige PR1-GH FSD
Summary of Contents for Prestige PR1-GH FSD
- Page 1 UILT-IN COOKING PR1-GH FSD Instructions for use Installation advice efore operating this cooktop, please read these instructions carefully KEEP IN S FE PL CE...
- Page 2 Dear Customer, Thank you for purchasing a Prestige Cooking Hob. The safety precautions and recommendations in these instructions are for your own safety and that of others. They will also provide a means by which to make full use of the features offered by your appliance.
-
Page 3: Important Precautions And Rec- Ommendations
IMPORTANT PRECAUTIONS AND REC- TIPS FOR THE USER OMMENDATIONS • During and after use of the cooktop, • After having unpacked the appliance, certain parts will become very hot. Do check to ensure that it is not dam- not touch hot parts. aged. - Page 4 FE TURES Fig. 1.1 CAUTION: COOKING SPOTS If the burner is accidentally extin- 1. Auxiliary burner (A) - 1,00 kW guished, turn the gas off at the 2. Semirapid burner (SR) - 1,75 kW control knob and wait at least 1 3.
-
Page 5: Gas Burners
HOW TO USE THE G S BURNERS GAS BURNERS LIGHTING THE BURNERS Gas flow to the burners is adjusted by In order to light the burner, you must: turning the knob illustrated in fig. 2.1 1 – Turn the knob fig. 2.2 in anti-clock- which control the safety valves. - Page 6 CORRECT USE OF TRIPLE-RING CHOICE OF THE BURNER BURNER (Fig. 2.4a - 2.4b) On the control panel, near every knob, there is a diagram that indicates which Flat-bottomed pans should be placed burner is controlled by that knob. directly onto the pan-support. The suitable burner must be chosen according to the diameter and the When using a WOK always place the...
-
Page 7: General Advice
CLE NING M INTEN NCE WARNING Important: When correctly installed, your prod- Before cleaning or carrying out uct meets all safety requirements laid any maintenance disconnect the down for this type of product catego- appliance from the electrical sup- ry. However special care should be ply and wait for it to cool down. - Page 8 BURNERS CORRECT REPLACEMENT OF THE BURNERS The burners can be removed and washed with soapy water only. It is very important to check that the They will remain perfect if always burner flame distributor F and the cap C cleaned with products used for silver- has been correctly positioned (see figs.
- Page 9 TRIPLE RING BURNER The triple ring burner must be correctly positioned (see fig. 3.3); the burner rib must be enter in their logement as shown by the arrow. The burners must be correctly positioned so that they cannot rotate (fig. 3.4). Then position the cap A and the ring B (fig.
- Page 10 DVICE INST LLER FOR THE IMPORTANT • The appliance should be installed, regulated and adapted to function with other types of gas by a QUALIFIED INSTALLATION TECHNICIAN. Failure to comply with this condition will render the guarantee invalid. The hob should only be installed by a suitably qualified and registered installer. •...
-
Page 11: Ventilation Requirements
LOCATION The appliance may be installed in a kitchen, Kitchen/diner or a bed sitting room, but not in a room or space containing a bath or a shower. The appliance must not be installed in a bed-sitting room of less than 20 m The appliance is designed and approved for domestic use only and should not be installed in a commercial, semi commercial or communal environment. - Page 12 INST LL TION TECHNICAL INFORMATION FOR THE INSTALLER Before installing the hob, remove the protective film. In order to install the cooker top into the kitchen fixture, a hole with the dimensions shown in fig. 4.1 has to be made, bearing in mind the follow- ing: •...
- Page 13 INSTALLATION IN KITCHEN CABINET Fig. 4.3 WITH DOOR (fig. 4.3) It is recommended that a 30 mm clear- ance be left between the cooker top and the fixture surface (fig. 4.3). Clearance Door Space for connections FASTENING THE INSTALLATION BRACKETS (fig.
-
Page 14: Gas Connection
G S SECTION GAS INSTALLATION IMPORTANT NOTE This appliance is supplied for use on NATURAL GAS only and cannot be used on any other gas without modification. This appliance is manufactured for conversion to LPG. To purchase an LPG conversion kit telephone accessories direct 0870 6052020. - Page 15 INSTALLATION TO LP GAS This appliance must only be connected to LPG after an LPG conversion kit has been fitted, (see pages from 16 to 17). When operating on Butane gas a supply pressure of 28-30 mbar is required. When using Propane gas a supply pressure of 37 mbar is required. The installation must conform to the relevant British Standards.
-
Page 16: Conversion To Lpg
CONVERSION TO LPG INJECTORS REPLACEMENT OF HOB BURNERS This appliance is manufactured for conversion to LPG. To purchase an LPG conversion kit telephone acces- sories direct 0870 6052020. The diameter is marked on the injector in cents of millimetre. Fig. 5.2 Select the injectors to be replaced according to the “Table for the choice of the injectors”. -
Page 17: Minimum Burner Setting Adjustment
MINIMUM BURNER SETTING ADJUSTMENT Check whether the flame spreads to all burner ports when the burner is lit with the gas tap set to the minimum position. If some ports do not light, increase the minimum gas rate setting. Check whether the burner remains lit even when the gas tap is turned quickly from the maximum to the minimum position. - Page 18 ELECTRIC L SECTION For your safety please read the following information Warning: This appliance must be earthed. • The appliance must be connected to a 220-240 volts 50 cycle AC supply by means of a three pin socket, suitably earthed and should be protected by a 3 amp fuse in the plug.
- Page 19 Your Prestige from COMET Your new Prestige product comes with 12-month guarantee covering all parts and labour. If your appliance proves to be defective as a result of faulty materials or workmanship during the guarantee COMET will repair or replace it free of charge.
- Page 20 Prestige is a registered trademark of Meyer Intellectual ® Properties Limited and is sold pursuant to a license. code 1103485 ß2...
Need help?
Do you have a question about the PR1-GH FSD and is the answer not in the manual?
Questions and answers