Related Manuals for ILY Enterprise SDC07-SSP
Summary of Contents for ILY Enterprise SDC07-SSP
- Page 1 USB, eUSB, CF, CFast , SD, Micro SD SD/Micro SD Combo Duplicator User’s Manual Version 7.0 All rights reserved © 2015...
-
Page 2: Table Of Contents
Table of Contents Introduction Features Control Panel Overview Specifications Warning Synchronous /Asynchronous Mode III. Synchronous Mode Asynchronous Mode Menu Overview Copy Compare Copy + Compare Capacity Check Utility Format FAT32 Format exFAT Measure Speed Quick Erase Full Erase DOD Erase Change Disk Signature Media Information Device Model... - Page 3 Unknown Format Check Before Copy Display Mode Start-up Menu Button Beep Show Result Time 6.10 Boot Password 6.11 Setup Password 6.12 Language 6.13 Clear Setup 6.14 Performance...
-
Page 4: Introduction
Introduction This duplicator system is designed and developed based on the FPGA from the world famous semiconductor company XILINX. Every processing channel is parallel to each other with its own control unit, therefore the duplicator will not sacrifice speed for the increasing number of targets loaded - always remain the same and fast copy speed. -
Page 5: Specifications
3. Specifications *Product specs may change without notice Model USB, eUSB, CF, CFast, SD, Micro SD, SD/Micro SD combo duplicator 7, 15, 20, 34, 48, 55, 63, 118 (other configurations available too) Target Standalone (No PC or Software is required) Operation USB/eUSB : USB 1.1/2.0/3.0 compatible devices, eUSB (embedded USB) Supported Media... -
Page 6: Synchronous /Asynchronous Mode
3. The Green LED flashes during the execution process of a task. After the task is done, the Green LED will stay solid if the process is successful, otherwise the Red LED will be on if the process is failed. 4. -
Page 7: Menu Overview
Asynchronous Mode to enable or disable this function. a. Insert source media into the source channel, select the task to execute from the menu, and press ENT button. Duplicator will start to execute the task now. b. Target devices can be plugged in during the execution process, and will start to execute the task immediately c. -
Page 8: Copy+Compare
3. Copy + C o m p are This command allows duplicator to start Copy process first, then follow with Compare process immediately. 3. Copy+Compare Copy& 7.8G &COMP 7.8G ： ： ： ： ： ： ： ： Ready device: 7 ：... -
Page 9: Measure Speed
[Utility] Sure to format? Format ： ： ： ： 1. Format exFAT ： ： ： ： ： ： ： ： Use ▲or ▼ to select option Display progress status Result: Pass Fail ： ： ： ： ： ： ： ： Final result 5.3 Measure Speed This option allows to measure the actual Read and Write speed of the target... -
Page 10: Change Disk Signature
be permanently deleted. It takes the longest time to erase, and the content will not be retrieved by software. [Utility] Sure to erase? DoD Erase ： ： ： ： 6. DoD Erase ： ： ： ： ： ： ： ： E N T E N T E N T... -
Page 11: System Update
[Utility] F0107V 128MB Controller Model Memory Firmware Target Number 10. System Info. V1.05.12 E N T E N T E N T E N T Display system information 5.11 System Update This option allows user to update the firmware of duplicator when necessary. Please obtain the proper firmware file from manufacturer, and save the unzipped file under home folder on the flash device (DO NOT save the file under sub folder). -
Page 12: Smaller Target
Asynchronous Mode is disabled. Please refer to Chapter III for the detail of operation on Synchronous and Asynchronous Mode. [Setup] [ [ [ [ A synchronous Mode ] ] ] ] 2. Asynchronous Mode Disable E N T E N T E N T E N T Use ▲or ▼... -
Page 13: Start-Up Menu
[Setup] [Display Mode] 6. Display Mode Basic E N T E N T E N T E N T Use ▲or ▼ to select Copy number of target ： ： ： ： 2.5G ： ： ： ： d ata to be copied Copy ：... -
Page 14: Show Result Time
Show Result Time This option allows to enable or disable the display of copy time after finishing the copy process. The default setting is disable. [Setup] [ [ [ [ S how Result Time ] ] ] ] 9. Show Result Time Disable E N T E N T... - Page 15 at the fastest speed, but may have compatibility issue with certain brands flash media. Balance mode is to execute the Copy function at stable speed, and have less compatibility issue with certain brands flash media. Compatibility mode is to execute the Copy function at the most stable speed, and almost have no compatible issue with flash media.
Need help?
Do you have a question about the SDC07-SSP and is the answer not in the manual?
Questions and answers