Table of Contents
Advertisement
6
Assembly Instructions (continued)
9
Lock Lid
Unlock Lid
10
Fold Up Legs
Note: Always lock lid before folding legs .
Unfold Legs
Note: Always open legs completely and are secured in place before lighting .
Outdoor LP Gas Barbecue Grill
Model No. NPG2302SS
Operating Instructions
This grill is designed to operate with a 1 lb .
7 .75 in . or 10 .6 in . high disposable / 16 .4 oz . or 14 .1
oz . propane gas tank (DOT 39 Cylinder) (Figure 1) .
DO NOT ATTEMPT TO REFILL ANY 1 lb. (16.4 oz. or
14.1 oz.) PROPANE GAS TANKS!
Connecting LP Gas Tank
Only cylinders marked "propane" may be used.
Note: 1 lb cylinders may form frost when near empty .
1 .
Make sure the regulator/control knob is in the
"OFF " position (Figure 2) .
2 .
Lubricate the threads of the regulator/control
knob with petroleum jelly . Line up threads on LP
gas tank with regulator/control knob .
3 .
Insert and rotate LP gas tank clockwise until
they fit snugly together . HAND TIGHTEN ONLY . Be
careful not to crossthread when screwing in tank
(Figure 3) .
4 .
Perform leak test per "Checking for Leaks"
section .
Disconnecting LP Gas Tank
1 .
Turn the regulator/control knob to the "OFF "
position (Figure 2) .
2 .
Rotate LP gas tank counterclockwise until it is
detached (Figure 4) .
3 .
Store the LP gas tank in a proper location, per
instructions on the LP gas tank .
Checking for Leaks
Burner Connections
1 .
Make sure the regulator/control knob is securely
fastened to the burner .
Note: The brass nut should be 1/4 to 1/2 turn past
tight . The regulator will rotate 360º even when the
brass nut is tightened .
If your unit was assembled for you, visually check
the connection between the burner and regulator/
control knob (Figure 5) .
W WARNING: Failure to inspect this
connection or follow these instructions
could cause a fire or an explosion
which can cause death, serious bodily
injury or damage to property.
2 .
If the burner and regulator/control knob do not
fit properly or if you have any questions, please
contact 1 .800 .762 .1142 for assistance .
Tank/Gas Line Connection
1 .
Make 2-3 oz . of leak detection solution by mixing
one part liquid dishwashing soap with three parts
water .
2 .
Make sure regulator/control knob is in the
"OFF " position (Figure 2) .
3 .
Spoon the leak detection check solution on all "X"
locations (Figure 5) .
a .
If any bubbles appear, remove the LP
gas tank and reconnect, making sure the
connection is secure .
b .
If you continue to see bubbles after several
attempts, remove the LP gas tank per
"Disconnecting LP Gas Tank" section, and contact 1 .800 .762 .1142 for assistance .
c .
If no bubbles appear after one minute, turn regulator/control knob to the "OFF "
position, wipe away solution and proceed .
First Use
1 .
Make sure all labels, packaging and protective films have been removed from the grill .
2 .
Remove manufacturing oils before cooking on this grill for the first time by operating
the grill for at least 15 minutes on (HIGH) with the lid closed . This will "heat clean" the
internal parts and dissipate odors .
Figure 1
1 lb
1 lb
453 g
453 g
3.875 in. / 9,8 cm
2.9 in. / 7,4 cm
Figure 2
Figure 3
Figure 4
Figure 5
X
X
Advertisement
Table of Contents
