Related Manuals for TE HL-1
Summary of Contents for TE HL-1
- Page 1 HL-1 HDMI Extender System Installation Manual HDBaseT IRDA Out HL-1 RX HDMI Extender Receiver with HDBaseT-Lite™ Power HDMI IRDA HDCP Link...
-
Page 2: Table Of Contents
HL-1 Installation Manual Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Kit Contents . -
Page 3: Introduction
HL-1 Installation Manual Introduction INTRODUCTION Thank you for purchasing Transformative Engineering’s HL-1 HDMI Extender Kit. This product incorporates many advanced technologies to accomplish full-function, 1.4a HDMI compliant extension of the High Definition MultiMedia Interface protocol over one length of Category 5e/6/7 wire. Among these is the newly certified HDBase-T technology, licensed here. -
Page 4: Kit Contents
HL-1 Installation Manual Kit Contents KIT CONTENTS (1) HL-1 Transmitter Unit (HL-1TX) (1) HL-1 Receiving Unit (HL-1RX) (1) 24V 8.5Watt Power Supply (4) Nylon “Tie-Wrap” Mounting terminals (2) Heat-Transfer tape Strips (4) Metal Mounting Tabs & Screws (1) User Manual... -
Page 5: Feature Set
HL-1 Installation Manual Features FEATURE SET • HDMI 1.4a Extender • Full HDCP Security • EDID Protocol Integrity • Bi-Directional IR Pass-Thru with Power for Active Pickup • 24V Power Supply for Robust Performance • Single Power Supply for Head-End Powering of Both Units... -
Page 6: Specifications
HL-1 Installation Manual Specifications SPECIFICATIONS Input Signal: HDMI Version 1.0 thru 1.4a Ethernet (10/100T) IR Signal – Pass Thru (Industry Compatible) IR Powered Pickup – Ring (Ground), Tip (Signal), Sleeve (+12VDC) (see page 8) Video Formats Supported: 480i/576i/480p/576p/720p/1080i/1080p Audio Formats Supported:... -
Page 7: Transmitter Connections
HL-1 Installation Manual Transmitter Connections TRANSMITTER HDMI Input IRDA OUT HDBase-T Link Connection Link Indicators Power Input HDCP Indicator IRDA IN... -
Page 8: Receiver Connections
HL-1 Installation Manual Receiver Connections RECEIVER HDMI Output IRDA OUT HDBase-T Link Connection Link Indicators IRDA IN HDCP Indicator... -
Page 9: Connection Diagrams
IRDA In – Used for connecting to a 12V Powered Infra-Red Pickup Device via 3-conductor mini-jack, or to IR encoded signal for Pass-Thru to the IRDA OUT at the Receiver end. Contact TE to purchase an adaptor if you are using a lower voltage IR device. See Diagram above for suggested use. - Page 10 HL-1 Installation Manual Recievers Functions HDCP Indicator – This light shows that a valid HDMI connection has been made, “handshake” has taken place, and there is a High Definition Copy Protect flag in operation. Attempts to copy Digital content will not be allowed.
-
Page 11: Troubleshooting
HL-1 Installation Manual Troubleshooting TROUBLESHOOTING As mentioned previously, most malfunctions can be addressed by careful examination of the Category cable terminations and suitability of the UTP cable itself. Once the “Link” lights are on, this system is operating normally. Lack of function should be traced to a failure in HDMI interconnection cables or device settings. -
Page 12: Warranty
HL-1 Installation Manual Warranty WARRANTY Transformative Engineering, Inc. guarantees this product for Two Years from your original purchase. We guarantee performance and operation to published specifications including all parts and labor. We do not warranty against mis-use or abuse. To obtain warranty service, please contact our Technical Support Department at 781-769-6410 or via email at: info@transformativeengineering.com.
Need help?
Do you have a question about the HL-1 and is the answer not in the manual?
Questions and answers