Advertisement

OWNER'S MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Ventura Vibe and is the answer not in the manual?

Questions and answers

Summary of Contents for DigiTech Ventura Vibe

  • Page 1 OWNER’S MANUAL...
  • Page 2: Warranty

    The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control.
  • Page 3 • Modern Vibrato • Rotary To use the Ventura Vibe pedal, enable the effect with the Footswitch (the LED will light when the effect is enabled). Set the MIX control to the 3 o’ clock position. Select the desired vibrato/rotary type with the TYPE switch.
  • Page 4: User Interface

    Connect the specified Harman power supply (sold separately) to this jack. Be sure to use the proper power supply for your area’s mains line voltage. See ‘Specifications’ on page 10 for power supply model information. The Ventura Vibe can only be powered using the external power supply. 3. DEPTH Knob Increases the intensity of the modulation effects.
  • Page 5: Indicator Led

    Controls the rate of the modulation effect. Turn the knob clockwise to increase the rate or counter- clockwise to decrease the rate. The Ventura Vibe gives you the flexibility to control the speed of the modulation effect during performance by pressing and holding the Footswitch while the effect is on. The Vibe’s LED will turn green and the speed will ramp up to the fastest speed for the selected type as long as the footswitch is held.
  • Page 6: Making Connections/Applying Power

    To connect the Ventura Vibe pedal to your rig: 1. Turn down the amplifier’s master volume control. 2. Make all audio connections to the Ventura Vibe as shown in ‘Connection Diagrams’ on page 3. Connect the appropriate Harman power supply (not included) to the POWER input connector and connect the other end to an available AC outlet.
  • Page 7 Amplifier Effects Loop Setup Harman FX SND FX RTN Power Supply OUT 1 (MONO) IN 1 (MONO) Other Effects Use only unbalanced TS instrument cables for audio connections. Optional NOTE: If the amp effects loop has a mix control, set the mix to 100% full wet.
  • Page 8: Example Settings

    Cold Shot Cold Shot Floyd Breath Floyd Breath EXAMPLE SETTINGS Try these settings to get started. Cold Shot Cold Shot Floyd Breath Floyd Breath S P E E D S P E E D D E P T H D E P T H S P E E D S P E E D D E P T H...
  • Page 9 Clapton Badge Clapton Badge Lucy Diamonds Lucy Diamonds Clapton Badge Clapton Badge Lucy Diamonds Lucy Diamonds S P E E D S P E E D D E P T H D E P T H S P E E D S P E E D D E P T H D E P T H...
  • Page 10 PERFORMANCE ACCESSORIES The performance accessories make integrating the Ventura Vibe pedal into any pedalboard a snap. The following accessories are included: • Hook-and-loop Pedalboard Pad (designed to attach to the surfaces found on most commercial pedalboards) • StompLock™ (keeps your settings where you want them)
  • Page 11 StompLock™ The included StompLock lets you lock your settings in place, while the open-top design lets you see your settings. To place the StompLock over the pedal knobs: 1. Set the knobs to your preferred settings. 2. Orient the StompLock so that it lines up with the knobs and gently push it over the top of the knobs.
  • Page 12: Specifications

    SPECIFICATIONS Interface Controls: Speed, Depth, Mix, Tone, Drive, Effect Type, Effect On/Off Jacks: Input 1 (Mono), Input 2, Output 1 (Mono), Output 2 Inputs Input Impedance: Effect on: >1 MΩ (stereo), >500 kΩ (mono) Effect off: >1 MΩ (stereo), >500 kΩ (mono) Effect off: True hardwire bypass Outputs Output Impedance:...
  • Page 13 PHONE: (801) 566-8800 WEB: digitech.com SUPPORT: digitech.com/en-US/support Ventura Vibe Owner's Manual 5064622-A © 2015 Harman. All rights reserved. DigiTech is a registered trademark of Harman.

Table of Contents

Save PDF