Miele K1803 Vi Installation Instructions Manual
Hide thumbs
Also See for K1803 Vi:
- Operating and installation manual (68 pages) ,
- Operating and installation instructions (68 pages) ,
- Operating and installation instructions (72 pages)
Table of Contents
Advertisement
Installation Instructions
Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.
K1803 Vi, K1813 Vi, K1903 Vi,
K1913 Vi
To prevent accidents
and machine damage
read these instructions
before
installation or use.
Advertisement
Table of Contents
Related Manuals for Miele K1803 Vi
Summary of Contents for Miele K1803 Vi
-
Page 1: Installation Instructions
Installation Instructions Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. K1803 Vi, K1813 Vi, K1903 Vi, K1913 Vi To prevent accidents and machine damage read these instructions before installation or use. -
Page 2: Caring For The Environment
Caring for the environment Disposing of the packaging Disposal of your old appliance materials Old appliances may contain materials that can be recycled. Please contract The packaging is designed to protect your local recycling authority about the the appliance from damage during possibility of recycling these materials. -
Page 3: Climate Range
Installation Installation site Have the appliance installed by a The appliance should be installed in a qualified technician, according to dry, well ventilated room. the enclosed installation instructions. Do not install the appliance: - outdoors, - in an environment with dripping WARNING water, This appliance is top-heavy and... - Page 4 Installation Important! When there is high humidity a build-up of condensation on the outer surfaces of the appliance can occur.This can cause the surfaces to corrode.To prevent this, it is advisable to install the appliance in a dry and/or an air-conditioned room with sufficient ventilation.Please ensure that doors close and seal properly after...
-
Page 5: Installation Niche
See "Niche dimensions". If in doubt, contact Miele. The side walls of the installation cavity must be plumb. Furniture/fixtures The minimum thickness of the side... -
Page 6: Stainless Steel Panels
The "Merging Kit" is available from Miele. This appliance is compatible with all styles and designs of kitchen cabinetry. Contact Miele or your dealer for The total weight of the decorative specific information about which panel(s) must not exceed the following: combinations will work with your appliance. -
Page 7: Side Panels
The "Merging Kit" will also be needed. The "Merging Kit" is available from Miele. Installation with partition without using the "Merging Kit" If there is a partition with a thickness of more than 6 "... - Page 8 To connect these furniture doors on the holes and drive in with a hammer. rear, a metal strip can be purchased as an optional accessory. Contact Miele. The door opening angle is now limited to 90°. When attaching the metal strip to the...
- Page 9 Dimensions Door dimensions (open min. 90°) *The dimensions of the door fronts and handles will vary according to each individual kitchen. " (10 mm) K 18X3 Vi " (829 mm) Door front max. 1 1/2" (38 mm) Door handle* K 19X3 Vi "...
- Page 10 Dimensions Niche dimensions Niche width (A) K 18X3 Vi 30" (762 mm) K 19X3 Vi 36" (915 mm)
-
Page 11: Power Supply
Dimensions Power supply 1. Power supply K 18X3 Vi 15" (381 mm) K 19X3 Vi 18" (458 mm) Power bars or extension cords are not safe (risk of fire). Do not use them to connect the appliance to the power supply. -
Page 12: Door Front Dimensions
Dimensions Door front dimensions K 18X3 Vi " " (2029 mm) (756 mm) K 19X3 Vi " " (2029 mm) (908 mm) 4" - 5 3/16" (102 - 132 mm) -
Page 13: Installing The Appliance
Installing the appliance Before you begin – Multi-grip pliers – Level Read these instructions completely and carefully. – Tape measure Have the appliance installed by a – Square qualified technician, according to When fastening the cabinet to the wall the enclosed installation behind it (see "Installing the appliance") instructions. -
Page 14: Aligning The Housing Unit
Installing the appliance Aligning the housing unit Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. ^ Check the base (see "Installation"). ^ Check the dimensions of the cavity. - Page 15 Installing the appliance Caution! The appliance is no longer secured and may be unstable. ^ From the rear of the appliance carefully lift it from the pallet. Once the appliance is on the ground it can be wheeled around. ^ Do not remove the installation supports from the appliance door.
-
Page 16: Preparing The Installation Niche
Tipping hazard. unsuccessful. In that case, repeat the process. If that does not correct the problem, contact Miele. Because of the size and weight of the appliance, it is essential to ensure that the appliance cannot tip over once it has been mounted in the niche. -
Page 17: Mounting Accessories
Installing the appliance Mounting Accessories The mounting accessories needed for installing the appliance into the niche are included in the packaging. Several plastic bags are included which are numbered alphabetically. The bag needed for each step will be marked with its respective letter. Two anti-tip brackets are recommended for each appliance. - Page 18 Installing the appliance In a cabinet without a back wall ^ Now attach the installation niche to the wall. The built-in cabinet must be secured to the wall behind it with several screws. In a cabinet with a back wall ^ screw the cabinet to the wall behind it in several places using suitable mounting brackets.
- Page 19 Installing the appliance Securing an alternative anti-tip – The beam must cover the appliance by at least 2" (50.8 mm). device ^ Mark the installation height (lower If the anti-tip brackets cannot be attached securely, an alternative edge of the beam) on the rear wall of anti-tip device can be used.
-
Page 20: Sliding The Appliance Into The Installation Space
Installing the appliance ^ Plug the appliance into the power Sliding the appliance into the outlet a. installation space The plug of the appliance should be If a side-by-side installation is easily accessible after installation. desired, connect the two appliances If the plug is not accessible after the together. -
Page 21: Aligning The Appliance
Installing the appliance Aligning the appliance Important! ^ Align the appliance with the custom When unscrewing the front. height-adjustable feet, proceed gradually, alternating between left and right. ^ Unscrew the height-adjustable feet until the mark on the base has reached the indicated guide dimension 1 1/4"... -
Page 22: Attaching The Appliance To The Installation Niche
Installing the appliance Attaching the appliance to the installation niche ^ Secure the attachment plate side lugs. If there is a fairly large gap above the ^ Screw the attachment plate lugs f to appliance, cut a wooden beam to fit the overhead furniture/fixtures. - Page 23 Installing the appliance ^ Open the appliance door. For a side-by-side combination the filler strips from both appliances are put together to form one long filler strip: ^ Take the peg from the "side-by-side merging kit" and insert it halfway into the filler strip rail on the left-side appliance.
-
Page 24: Preparing The Custom Door
Installing the appliance Preparing the custom door ^ Open the appliance door. ^ Unscrew the installation supports l ^ Measure the distance X between the from the appliance door. bracket from the door and the ^ Loosen the remaining screws from overhead furniture/fixtures. - Page 25 Installing the appliance ^ Mark the distance X on the back-side Please note: When attaching the of the custom door. mounting frame onto two adjacent ^ Also calculate and mark the center of doors (see "Front panel gap kit") the custom door Y. screw into the thicker outer frames ^ Remove the mounting frame from the of the doors only.
- Page 26 Installing the appliance Attaching and aligning the custom door front ^ Align the custom door height with the threaded bolts n. ^ Now tighten the nuts o on top. This secures the appliance door. ^ Open the door and hang the custom door with the mounting frame over the threaded bolts n.
-
Page 27: Attaching The Covers
Installing the appliance Attaching the fixing brackets Attaching the covers (Only for appliances using the "Front panel gap kit".) ^ To mount the cover strips on both sides of the door, click them into place from bottom to top, into the The fixing brackets are used to secure gap between the appliance door and the custom door front to the bottom of... - Page 28 Installing the appliance Attaching the toe-kick cover The maximum height of the toe-kick cover is 4" (101 mm) from the top of the floor. Do not cover the ventilation slits in the plinth. Risk of damage to the appliance. ^ If required, cut the toe-kick cover to the required length and height.
- Page 29 Installing the appliance ^ Remove the foil from the adhesive strips. ^ Attach the toe-kick cover to the plinth. ^ Position the air separator in the Mounting the air separator center of the appliance door. The air separator keeps the supply and ^ From below, screw the air separator exhaust air separate.
-
Page 30: Electrical Connection
If there are any questions regarding the electrical connection of this appliance to the power supply, please consult a licensed electrician or call the Miele Technical Service. U1-800-999-1360 V1-800-565-6435... -
Page 31: Remotevision (Optional Accessory)
'virtual link' between your following requirements appliance and our monitoring center. If – A wireless router that supports an a fault occurs, Miele's client service IEEE 802.11b/g protocol center will be notified and contact you, ® or another trusted individual identified –... -
Page 32: Accessing The Remotevision Control Panel
RemoteVision (optional accessory) ^ Tap the X button until ; appears in Accessing the RemoteVision the display. control panel ^ Touch the access button "p" to confirm. See the table on the following page for a description of each setting in the ^ Touch the access button "p"... - Page 33 RemoteVision (optional accessory) MasterCool control panel options for RemoteVision Status indicators Description of function Flashing ; ~ Module booting phase Flashing ; ‡ Not connected to network Flashing ; | Connection to network established, no IP address assigned Solid Connected to network Flashing ;...
- Page 38 K 1803 Vi, K 1813 Vi K 1903 Vi, K 1913 Vi en - US, CA M.-Nr. 09 920 570 / 00...