Table of Contents
Advertisement
7
Turning on Your .VCR-
TV and VCR
CH3 [_
CH,
Press the VCR button,
then the POWER
button.
3y
Press the Number
1
button for English on-
screen displays or the
Number 2 button for
Spanish on-screen
dis-
plays.
@_-
00000
O0
O0
1
Set the TV to channel
3 or 4, whichever
channel.the
CH3/CH4
switch on the back of
the VCR is set to.
Remote
Control
-5
Press the CHANNEL
(Up) button.
-4
Press the MENU
button.
• If you do not see any on-screen
displays
when you turn on the VCR, repeat
the steps under "Hooking
Up Your VCR" on page six, then try again.
If
you still do not see any on-screen
displays, follow
the steps under "Channel
Memory"
on page 27 and "Language
Selection"
on page 28.
• To skill this feature
andplay
a tape immediately,
insert a tape with its
record tab removed.
Playback
will start immediately.
Or, to skip step 3,
press the MENU button.
All on-screen
displays
will be in English.
To skip
step 5, press the STOP button.
Channels
will not be programmed,
and
TUNER NOT SET will appear on-screen.
• To program
channels
or to change
the language
at a later time, follow
the
steps on pages 27 and 28.
• lfyou
try to program
channels
when there is no antenna or cable connected
to the VCR, programming
will appear to take place,
but eventually
NO TV
SIGNALS
will appear on-screen.
Connect
an antenna
or cable to the VCR
and try again.
You may need to follow
the steps on page 27.
• You cannot program
channels
ifa cable converter
box is connected
to a
VCR that is connected
to a TV. If you have this kind of connection,
see
pages 36-39for
details.
• Follow the steps on this page only when you plug the VCR power
cord into
the wall outlet for the first time.
• The VCR distinguishes
between
standard
TV channels
and cable channels.
lf you change to TV or CABLE
TV mode, follow
the steps under "Channel
Memory"
on page 27.
Before turning on your VCR, make sure
there are batteries in the remote control and
the VCR and TV are connected (see pages
five and six).
1
Turn the TV on. Set it to the same channel
as the CH3/CH4 switch on the back of the
VCR.
2
Press the VCR button, then the POWER
button.
The VCR will come on and the lan-
guage select display
screen shown below
will appear.
SELECT PUSH NO. SHOWN_
ENGLISH
ON
[
ESPNTX)L
1
E SELECTIONOR
]
H MENUTO CONTINUE)
3
Press the Number 1 button to select English
on-screen displays or the Number 2 button
to select Spanish on-screen displays.
4
Press the MENU
button.
The channel
pro-
gram display
shown below will appear.
The
display
will disappear
after about 60 sec-
onds if you do not press any buttons.
_NECT
ANTENNA OH CABL_
TO VCR
/
THEN...
l
PUSH OH UP KEY
/
_O;LAY
ONLY- PUSH STOP_
5
i
Press the CHANNEL
(Up) button to begin
"
automatic
channel
programming.
AUTO
!
SET PROCEEDING
PLEASE
WAIT will
appear
on-screen.
The VCR will place all
: of the channels
you receive into its memo-
! ry, so when you scan through
channels
using the CHANNEL
(Up/Down)
buttons,
i
you'll
only scan through channels
that you
:
receive.
When all channels
are pro-
i
grammed,
AUTO SET COMPLETED
will
i
appear on-screen
briefly.
Then the TV will
:
go to the lowest channel
programmed.
Advertisement
Table of Contents
