Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for xG Technology CN3200-PS-2500-900-1-EXT
Summary of Contents for xG Technology CN3200-PS-2500-900-1-EXT
- Page 1 G7604 - Release 1.0...
- Page 2 Product features and specifications are subject to change without prior notice. xG® and xMax® are registered trademarks of xG Technology, Inc. All other trademarks used herein are property of their respective owners. For the latest product documentation and software updates, please refer to our Web site at www.xGTechnology.com/support...
-
Page 3: Table Of Contents
Table of Contents Introduction ....................... 5 About this Product ........................5 About this Book ........................5 Before You Begin ........................5 Hardware Overview ....................6 Powering the CN3200 Modem ....................6 Connectors ..........................7 Status LED ..........................7 Antenna Considerations ..................... 8 Antenna Configuration ...................... - Page 4 THIS PAGE INTENTIONALLY LEFT BLANK CN3200 Dual Band Routing Modem - Installation Guide - G7604 - Release 1.0...
-
Page 5: Introduction
The CN3200 Dual Band Routing Modem is a ruggedized subscriber device. It is waterproof and made to handle wide temperature ranges. While primarily designed for use in fixed locations, it may also be used in vehicular applications. It enables any Internet-ready device to connect to the xMax network, when paired with a WiFi access point either wirelessly or through a wired Ethernet connection. -
Page 6: Hardware Overview
The CN3200 Dual Band Routing Modem provides any device connected to its Ethernet port access to the xMAX network and xMax modem. When paired with a WiFi hotspot it provides access to the xMAX network to WiFi enabled devices. Alternately, any Ethernet capable device can access the network via the Ethernet port. -
Page 7: Connectors
The CN3200 Modem features seven connectors (one is unused): Four external xMax antenna connectors (N-type / female) on the base A connector for an external 2.4 GHz antenna (TNC-type / female) on the top cover A weatherproof Ethernet connector for data and PoE (Power-over-Ethernet) on the base ... -
Page 8: Antenna Considerations
The CN3200 Modem is a 2x4 MIMO device with four antenna connectors — two Tx/Rx and two Rx-only. All connectors are always used. The CN3200 Modem is mounted directly to the back of the xMax 900 MHz panel antenna using the supplied bracket. - Page 9 This is a typical tower-mounted CN3200 Modem installation with a 2x4 MIMO Panel Antenna. xMax IMPORTANT Antenna Install the eight (8) provided ferrite beads, as shown by this marker in the wiring 2.4 GHz diagram. Antenna 110-240 VAC, 50/60 Hz PoE++ Power Supply Surge...
-
Page 10: Important Safety And Installation Requirements
Be sure to read, understand and follow these instructions. Heed all warnings. Only use accessories and attachments specified by xG Technology. Keep a copy of these instructions for future reference. The CN3200 Dual Band Routing Modem MUST only be installed by a professional installer. -
Page 11: Rf Exposure
Changes or modifications to this device not expressly approved by xG Technology could void the user’s authority to operate the equipment and void the product warranty. CN3200 Dual Band Routing Modem - Installation Guide - G7604 - Release 1.0... -
Page 12: Configuring The Cn3200 Dual Band Routing Modem For The First Time
These steps set up the CN3200 Dual Band Routing Modem for use. After completing these configuration steps, the CN3200 Modem will be fully functional and ready for operation. It will broadcast on the configured channel. The CN3200 Modem will provide any Internet- ready device the ability to connect wirelessly to the xMax network, using a secure connection on a connected WiFi router. -
Page 13: Xmax Network Management
3. The menu bar is at the top of the window. On the left side of the menu bar, click WiFi and then, in the Wireless Settings section, update the security settings. xG Technology strongly recommends that you change the SSID and WPA security key. CN3200 Dual Band Routing Modem - Installation Guide - G7604 - Release 1.0... -
Page 14: Wifi Network Management
4. After confirming that the settings are written down, click Save Changes. xG Technology strongly recommends that you change the User Password. 6. To change the User Password, on the right side of the menu bar, click Admin. NOTES ... - Page 15 3. The Router Password page opens. NOTE The password is case sensitive. Before clicking Save & Apply, be sure to write down the new password for future reference: New Password: 4. On the Router Password page, enter a password in the Password field, and then enter it again in the...
-
Page 16: Installation
This checklist may assist you in assembling the parts needed to complete the installation. SUPPLIED BY xG Technology OBTAIN FROM YOUR PART SUPPLIER CN3200 Modem Ethernet Cable (Length as required) with Wall Mount Bracket Grounded PoE Surge Protector ... -
Page 17: Installation Preparation
These steps outline the basic tasks required to complete a successful installation. Your specific steps will depend upon the requirements of your system design. These initial steps prepare the CN3200 Dual Band Routing Modem for placement in a service location. Locate the supplied CN3200 Modem mounting bracket and secure the CN3200 Modem to the bracket with 4 hex-head screws, as shown. -
Page 18: Installation Procedure
1. Select an appropriate location and, using the supplied U-bolt mounting bracket, lightly secure the CN3200 Modem/xMax Antenna assembly to the antenna mast. 2. Orient the antenna towards the xMax Network station and then securely tighten the nuts on the U-bolt. - Page 19 12. Secure the Ethernet cable to the grounded PoE Surge Protector. 13. Install the supplied PoE++ Power Supply near the PoE Surge Protector. 14. Using a short Ethernet cable, connect the PoE Surge Protector to the Power plus Data (OUT) port on the PoE++ Power Supply. 15.
-
Page 20: Connecting The Cn3200 Dual Band Routing Modem To The Xmax Network
IMPORTANT Before you begin this step, it is assumed that the CN3200 Dual Band Routing Modem has been configured as described in the steps shown in the topic: Configuring the CN3200 Dual Band Routing Modem for the First Time on page 12. These steps connect the CN3200 Modem to an xMax network. -
Page 21: Connecting Wireless Devices To The Xmax Network
When within range of a WiFi router connected to the CN3200 Dual Band Routing Modem, any Internet-ready device has the ability to securely connect to the Internet through the xMax Network. These steps connect WiFi devices to the xMax Network. 1. -
Page 22: Wired Internet Connectivity And Setting Up A Wifi Hotspot
A properly configured device, such as a PC or laptop computer, can be wired directly to the CN3200 Dual Band Routing Modem for Internet access. 1. Configure the device network interface for DHCP operation. 2. Using an Ethernet cable, connect the device to the CN3200 Dual Band Routing Modem. The CN3200 Modem can be used to create a WiFi hotspot. -
Page 23: Technical Specifications
xMax RADIO Tx Power Output AVG: RANGE: 5 to 24 dBm in 1 dB steps Receiver Sensitivity -100 dBm BPSK / -90 dBm QAM64 2.4 GHz RADIO Tx Power Output AVG: 8.5 to 21 dBm in 1 dB steps Tx Power Output AVG: Receiver Sensitivity -93 dBm BPSK / -74 dBm QAM64 SYSTEM OVERVIEW... -
Page 24: Warranty
Resellers, and is not assignable or transferable to any subsequent purchaser or end- user. xG’s warranty applies only to a Product that is manufactured by or for xG Technology and is identified within xG’s price book at time of purchase . Any products not covered by xG’s warranty,... -
Page 25: Additional Provisions Of The Warranty
Customer is responsible for shipment to xG (or authorized service provider) and assumes all costs and risks associated with this transportation; return shipment to the Customer will be at xG’s expense. Customer shall be responsible for return shipment charges for Product returned where xG determines there is no defect ("No Defect Found"), or for Product returned that xG determines is not eligible for warranty repair. -
Page 26: Obtaining Service And Support Under Warranty
OBTAINING SERVICE AND SUPPORT UNDER WARRANTY To obtain warranty service or technical support, please contact the party from whom you purchased the product. If you purchased the product directly from xG, contact your xG Sales Representative or call 754-206-4800. To take advantage of this Limited Warranty Purchasers are required to supply an original point of purchase receipt. - Page 27 THIS PAGE INTENTIONALLY LEFT BLANK CN3200 Dual Band Routing Modem - Installation Guide - G7604 - Release 1.0...
- Page 28 Technology, Inc. 240 South Pineapple Avenue, Suite 701 Sarasota, FL 34236 (941) 953-9035 © Copyright xG Technology, Inc. 2014. All Rights Reserved www.xGTechnology.com G7604 - Release 1.0...