Page 1
Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX SUPPORT FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 INFORMATION Web site: www.blackbox.com • E-mail: info@blackbox.com...
Page 2
DRD-4 FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication.
2.2 Ports on the DRD-4 ..............5 2.3 Functions of the DRD-4 ............... 7 3. Installing the DRD-4 ................8 3.1 Installing the DRD-4 on a Single Line ........8 3.2 Installing the DRD-4 on a Single Line with Multiple Phones and Maintaining Exclusion..........10 3.3 Installing the DRD-4 on Two Lines with Single-Line and...
2.2 Ports on the DRD-4 eliminiating the need to flip switches and turn machines on or off. The rear panel of the DRD-4 includes five modular ports and a power input port, as shown in Fig. 2-1. STYLE 1...
STYLE 4 answer all phone calls during the ring signal. Once you answer a call, the DRD-4 will not allow any of its ports to interrupt a call to another port. This feature ensures your privacy during...
Page 7
DRD-4 CHAPTER 2: Introduction Connect your telephone equipment STYLE 2 port—This port rings with to the modular ports, as follows: a short-short ring cadence. Use this port for any telephone device that TEL LINE-IN port—The incoming you wish to respond to the second telephone line plugs into this port.
DRD-4 3. Installing the DRD-4 You can install the DRD-4 on any To install the DRD-4, you will need system with single- or two-line the telephone cable (included) and phones, including key service unit an additional cable for each device (KSU) or private branch exchange you wish to connect to the DRD-4.
Page 9
STYLE 1 STYLE 3 LINE-IN STYLE 4 PHONE Fig. 3-1. Installing the DRD-4 on a Single Telephone Line. To install the DRD-4 on a single line, 3. Plug one end of the telephone follow these steps: cable provided with the DRD-4 into the TEL LINE-IN port on 1.
DRD-4. installation. Call Technical Support Phones not connected directly to for instructions or contact a the DRD-4 will ring with each ring professionai installer. cadence and will be able to interrupt any call. For total automatic...
STYLE 2 STYLE 1 STYLE 3 LINE-IN STYLE 4 Fig. 3-2. Installing the DRD-4 on a Single-Line, Multiple-Phone System Maintaining Exclusion. 3.3 Installing the DRD-4 on Two For this procedure, you will need two three-way adapters, which you Lines with Single-Line and Two-Line...
Page 12
L1 port on one of the STYLE 1 port on the rear of the three-way adapters. Plug the DRD-4. Plug the other end of other end of the cable into the the cable into the L2 port on the...
Page 13
CHAPTER 3: Installing the DRD-4 STYLE 2 STYLE 1 STYLE 3 3-WAY ADAPTER L1+L2 LINE-IN STYLE 4 TWO-LINE TELEPHONE L1+L2 3-WAY ADAPTER Fig. 3-4. Installing the DRD-4 with a Two-Line Phone Using Three-Way Adapters.
DRD-4 3.4 Installing the DRD-4 on a Fig. 3-5 shows the DRD-4 connected to a KSU phone system. For the KSU/PBX System DRD-4 to operate correctly with such a system, you must install it in front With a KSU/PBX (commonly used of the KSU or PBX—directly to the...
Page 15
CHAPTER 3: Installing the DRD-4 KSU/PBX INCOMING LINES STYLE 2 STYLE 1 STYLE 3 LINE-IN STYLE 4 AC OUTLET Fig. 3-5. Installing the DRD-4 on a KSU Phone System.
DRD-4 4. Using the DRD-4 You can connect the DRD-4 to any • Fax machines four telephone devices. The DRD-4 • Order-taking systems will automatically direct all incoming calls to their intended destinations. • Bulletin-board systems If you are using any data devices,...
CHAPTER 5: Troubleshooting 5. Troubleshooting Table 5-1. Troubleshooting Chart. Problem Solution When I pick up a Connect the DRD-4 as shown in Section 3.2. phone, I interrupt another call. One of my telephone 1. Check all wiring connections. devices won’t respond 2.