1. Manuals
  2. Brands
  3. Aquavibe Manuals
  4. Controller
  5. MRC-2U
  6. Operation and installation manual

Aquavibe Universal Watertight Marine Radio Controller with Speed Indicators MRC-2U Operation And Installation Manual

Universal watertight marine radio controller with speed indicators
Hide thumbs Also See for Universal Watertight Marine Radio Controller with Speed Indicators MRC-2U:
Table of Contents

Advertisement

Quick Links

Download this manual
Operation
and Installation
Manual
MRC-2U
Universal Watertight Marine Radio Controller
with Speed Indicators

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Universal Watertight Marine Radio Controller with Speed Indicators MRC-2U and is the answer not in the manual?

Questions and answers

Related Manuals for Aquavibe Universal Watertight Marine Radio Controller with Speed Indicators MRC-2U

Summary of Contents for Aquavibe Universal Watertight Marine Radio Controller with Speed Indicators MRC-2U

  • Page 1 Operation and Installation Manual MRC-2U Universal Watertight Marine Radio Controller with Speed Indicators...

  • Page 2: Table Of Contents

    Index Introduction ..............3 Safety Information .

  • Page 3: Introduction

    Introduction Please carefully read all of the information in this manual. Familiarity with operation and installation proce- dures will help you obtain the best possible performance from your new Marine Radio Controller. Safety Information DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF.
  • Page 4 General Operations Selecting a Source/Mode: To select a play source, press the SRC button until the desired source/mode is selected. Volume: Increase the volume by pressing the VOL + button. Increase the volume by pressing the VOL - button. Mute: Press the button to mute the volume level.

  • Page 5: Removing The Remote

    Removing the Remote Removing the Remote from Holder: Press the release tab and slide out the remote. To reinstall, slide the remote into the holder until it snaps into place. Remote Installation Inserting Strap: Insert strap through the remote holder with tabs facing outward.

  • Page 6: Wiring Diagram

    Wiring Diagram Antenna Wire Do Not Cut or Connect Green LED Red LED (Speed-Up) (Slow-Down) Note: Receiver’s housing is not waterproof and must be mounted in a dry location. Red Wire +12 Volt Switch Black Wire Ground Infrared Emitter Attach to radio’s infrared receiver.

  • Page 7: Learning The Radio's Remote Code

    Learning the Radio’s Remote Code First, see if your radio is in the Manufacturer’s Code Look-Up Table below. If your radio is listed in the table go to “Automatic Code Learning”. If you can not find your radio in the list go to “Manual Code Learning”. Note: This receiver will only retain the one Radio Remote Code.
  • Page 8 Automatic Code Learning Step 5 5 Times To exit programming push the switch on/off 5 times or wait 15 seconds and the system will automatical- ly exit the “Automatic Code Learning” mode. Manual Code Learning Step 1 Turn on the power to the receiver’s Press and hold the button on the receiver for 7 seconds.
  • Page 9 Manual Code Learning Using the RF Marine Remote press the corre- sponding “VOLUME UP” button to assign this function. Step 5 Repeat Step 3 and 4 for the remaining 7 buttons. Each button has a unique LED flash indicator confirming when they have been programmed. Power On/Off Button = 1 Flash Volume Up Button = 2 Flashes...

  • Page 10: Learning An Additional Aquavibe Marine Remote Controller Code

    Learning an Additional Aquavibe Marine Remote Controller Code The Aquavibe Marine Remote Controller is already pre-programmed to the receiver. No programming is necessary. If you want to program additional Aquavibe Marine Remote Controllers follow the instructions below. Note: This receiver will only retain the 4 Marine Remote Controller codes. If the receiver’s memory is exceeded, the receiver will start deleting transmitters codes from memory in chronological order.

  • Page 11: Clearing All The Aquavibe Marine Remote Controller Codes

    Clearing All the Aquavibe Marine Remote Controller Codes Step 1 Turn on the power to the receiver’s housing. Step 3 Flashes 4 Times Press 2 Times and Hold Push the receiver button 2 more times, holding on the last push. The LED will flash 4 times indicating that all remote codes are cleared.

  • Page 12: Warranty

    Warranty ONE (1) YEAR LIMITED WARRANTY Magnadyne Corporation or its authorized agents will within one year from the date of sale to you, repair, replace or refund the retail sales price of said product or any part thereof, at the option of the Magnadyne Corporation or its authorized agents, if said product or part is found defective in materials or workmanship, when properly connected and operating on the correct power requirements designated for the specific product.

Table of Contents