Related Manuals for ELICA Lugano ELG636SS
Summary of Contents for ELICA Lugano ELG636SS
- Page 1 Use, Care, and Installation Guide Guide d’utilisation, d’entretien et d’installation Guía de instalación, uso y mantenimiento READ AND SAVE THESE INSTRUCTIONS LISEZ CES INSTRUCTIONS ET CONSERVEZ-LES LEA Y GUARDE ESTAS INSTRUCCIONES...
-
Page 3: Important Safety Notice
READ AND SAVE THESE INSTRUCTIONS Important safety Notice WARNING CAUTION TO REDUCE THE RISK OF INJURY TO PERSONS, IN FOR GENERAL VENTILATING USE ONLY. DO NOT USE THE EVENT OF A RANGE TOP GREASE FIRE, EXHAUST HAZARDOUS EXPLOSIVE OBSERVE THE FOLLOWING: MATERIALS OR VAPOURS. -
Page 4: Electrical & Installation Requirements
Electrical & Installation requirements Electrical requirements Before installing the hood 1. For the most efficient air flow exhaust, use a straight run IMPORTANT or as few elbows as possible. Observe all governing codes and ordinances. CAUTION: Vent unit to outside of building, only. It is the customer’s responsibility: 2. -
Page 5: List Of Materials
List of Materials Parts supplied Parts not supplied Removing the packaging Optional Accessories CAUTION! • Ductless Recirculating Kit Remove carton carefully, Wear gloves to protect against To be used only in the Ductless (Recirculating) sharp edges. version includes: charcoal filter, charcoal filter support and WARNING! fixing bracket, deflector Remove the protective film covering the product before... -
Page 6: Dimensions And Clearances
Dimensions and Clearances *Ductless (Recirculating) version Only **Ducting version Only... -
Page 7: Ducting Options And Examples
Ducting Options and Examples Closely follow the instructions set out in this manual. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined. Venting methods The hood is equipped with a transition B for discharge of fumes to the outside (Ducting version). Should it not be possible to discharge cooking fumes and vapour to the outside, the hood can be used in the Ductless (Recirculating) version. -
Page 8: Installation - Ducting Version
Installation Installation - Ducting version • If possible, disconnect and move freestanding or slide-in Ceiling ducting range from cabinet opening to provide easier access to If the duct will vent straight up to the ceiling: rear wall. Otherwise put a thick, protective covering over •... - Page 9 Install framing for hood support • If drywall is present, mark the screw hole locations. Remove the template. • Cut away enough drywall to expose 2 vertical studs at the holes location indicated by the template. Install two horizontal supports at least 4" X 2" between two wall studs at the bottom and upper mounting holes installation location.
- Page 10 Electrical connection Mounting the duct cover Note: Upper Duct Cover may be placed upside down to WARNING hide (or unhide) louver holes. Electrical Shock Hazard • Position the duct cover over the mounted hood. Warning: Turn off power circuit at the service panel •...
-
Page 11: Installation - Ductless (Recirculating) Version
Installation - Ductless (Recirculating) version House wiring location CAUTION The junction box is located on the top left side of the To install the hood in this version, first purchase the hood. Ductless Recirculating Kit. Wiring should enter the back wall at least 20 - 1/4" includes: charcoal filter and deflector above the bottom of the installation height, and within 7- 5/8"... - Page 13 Mounting the duct cover Electrical connection Note: Upper Duct Cover may be placed upside down to hide (or unhide) louver holes. WARNING Position the duct cover over the mounted hood. Electrical Shock Hazard Slide the bottom of the duct into the canopy area. Warning: Turn off power circuit at the service panel Position the top of the duct over the duct mounting before wiring this unit.
-
Page 17: Maintenance
Maintenance ATTENTION! Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket. Cleaning Replacing the light bulb Do not spray cleaners directly to the control while...
Need help?
Do you have a question about the Lugano ELG636SS and is the answer not in the manual?
Questions and answers