Safety instructions Ensure that the protective Delivery conductor system 1. Check the packaging and of the domestic supply has dishwasher immediately for been correctly installed. damage caused in transit. Do The electrical connection not switch on a damaged conditions must correspond appliance, but contact your with the specifications supplier.
Safety instructions After installing the appliance, Damage ensure that the plug is easily The appliance may be accessible. repaired and opened up by a (See Electrical connection) technician only. To do this, Some models: disconnect the appliance The plastic housing on the from the power supply.
Safety instructions In the case of free-standing Keep children away from appliances, ensure that the detergents and rinse aid. baskets are not overloaded. These may cause chemical burns in the mouth, throat If the appliance and eyes or asphyxiation. is not in a cavity and a side panel is accessible, the door Keep children away from hinge area must be covered...
Water softening system/Special salt Overview of menu Setting The amount of salt dispensed can be The settings can be found in the set from to : individual chapters. Salt is not required at the set value Water Hardness : Intensive drying : 1.
Water softening system/Special salt As soon as the salt refill indicator @ Water hardness table on the fascia is lit, top up the salt. :DWHU +DUGQHVV PPROO 6HW YDOXH KDUGQHVV UDQJH RQ WKH YDOXH PDFKLQH &ODUNH ¯¯ VRIW ¯³...
Rinse aid 3. Close cover until it clicks shut. Rinse aid 4. To prevent excessive foam formation a i d R i n s e during the next rinse cycle, remove any rinse aid which has run over with As soon as the rinse-aid refill indicator H is lit on the fascia, there a cloth.
Utensils Switching off rinse aid refill Recommendation: indicator Use only glasses and porcelain which the manufacturer designates as dishwasher-proof. If the rinse-aid refill indicator H is Use a detergent which protects impaired (e.g. when using combined utensils. detergents containing rinse aid component), it can be switched off.
Utensils Cups and glasses Other examples, such as the best way Top basket 12 of loading your dishwasher, can be found on our homepage as a free download. The corresponding Internet address can be found on the back page of these instructions for use. Cutlery drawer Arrange the cutlery in the cutlery drawer 1* as illustrated.
Utensils Small accessories holder * Sm a l l ac c e s s o r i e s ho l d e r * depending on model &/,&. Light-weight plastic accessories, e.g. cups, lids, etc. can be held securely in the small accessories holder.
Detergent 1. Pull out the top basket 12 out. Detergent 2. To lower the basket, press in the left and then the right lever on the D e t e r g e n t outside of the basket. In doing so, You can use tablets as well as powder hold the sides of the basket along or liquid detergents for dishwashers, but...
Detergent Adding detergent If the utensils are only lightly soiled, 1. If the detergent dispenser 9" is still slightly less than the indicated amount closed, press the lock 9* to open of detergent is usually adequate. the detergent dispenser. Suitable detergents and care products Pour detergent into the dry detergent can be purchased online dispenser 9"...
Detergent Notes You will obtain optimum rinsing and drying results by using solo detergents and applying salt and rinse aid separately. If programmes are short, tablets may not have full cleaning effect due to different dissolving properties and there may even be undissolved detergent residue.
Overview of programmes Overview of programmes p r o g r a m m e s O v e r v i e w o f The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
Additional options · Information for test institutes Hygiene * Hy g i e n e Test institutes receive the information for The temperature is increased during the comparability tests (e.g. according to cleaning process. This increases the EN60436). hygiene status. This additional option is ideal for cleaning e.g.
Operating the appliance Optical display while Remaining running time Op t i c a l d i s p l a y wh i l e t h e p r o g r a m m e i s r u n n i n g the programme is running * display * depending on model...
Operating the appliance End of programme Automatic switch off after end of programme or interior light* Au t o m a t i c s w i t c h of f / i n t e r i o r l i g h t The programme has ended when the value : is indicated on the numerical...
Operating the appliance To change the setting: Interrupting the programme 1. Press programme button 3. 1. Open the door. Each time the button is pressed, 2. Switch off ON/OFF switch (. the set value increases by one level; when the value of : has been The LEDs go out.
Cleaning and maintenance Intensive drying Overall condition of the machine The final rinse uses a higher temperature which improves the drying Check spray arm for grease result. The running time may increase and limescale deposits. slightly. (Caution if utensils are delicate!) If you find such deposits: 1.
Cleaning and maintenance Filters Spray arms The filters 1Z keep large foreign Limescale and contaminants in the objects in the rinsing water away from rinsing water may block nozzles and bearings on the spray arms 1: and the pump. These foreign objects may occasionally block the filters.
Fault, what to do? Fault table Fault Cause Remedial action “Check water supply” Supply hose kinked. Install supply hose without kinks. display 8 lights up. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min.
Fault, what to do? Fault Cause Remedial action A different error code is A technical fault has probably Switch off appliances with the ON/OFF switch (. After a short time restart indicated on the digital occurred. display. the appliance. to : If the problem recurs, turn off the tap and pull out the mains plug.
Fault, what to do? Fault Cause Remedial action Utensils not dry. No or too little rinse aid Refill rinse aid. in the dispenser. Programme selected without Select programme with drying (see drying. Overview of programmes, Programme sequence). Water collecting in depressions Arrange utensils in a sloping position, on the utensils and cutlery.
Fault, what to do? Fault Cause Remedial action Food remnants Utensils placed too closely Arrange utensils with adequate clearance on the utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points.
Fault, what to do? Fault Cause Remedial action Water stains on plastic Droplet formation on plastic Use a more intensive programme (more parts surface is physically unavoidable. water changes). After drying, water stains are Arrange utensils in a sloping position. visible.
Fault, what to do? Fault Cause Remedial action Coloured (blue, yellow, Film formation consisting Can be partly removed with machine brown), difficult to remove of ingredients from vegetables cleaner or by mechanical cleaning. Coatings to non-removable coatings (e.g. cabbage, celery, potatoes, are harmless.
Fault, what to do? Fault Cause Remedial action Rust spots on the cutlery. Cutlery not adequately rust- Use corrosion-resistant cutlery. resistant. Knife blades are frequently more severely affected. Cutlery will also rust if rusting Do not wash rusting parts. parts are rinsed at the same time (pan handles, damaged utensil baskets, etc.).
Fault, what to do? Fault Cause Remedial action Appliance stops Door not closed properly. Close the door. in the programme or Do not place utensils or fragrance Check whether rear panel is being pressed programme is interrupted. dispenser in the tablet collecting in, e.g.
Customer service Customer service Installation and connection e r v i c e C u s t o m e r s If you are unable to rectify the fault, i o n a n d c o n n e c t l a t i o n I n s t a l please contact your customer service.
Installation and connection Delivery Installation Your dishwasher has been checked The required installation dimensions can thoroughly in the factory to ensure that it be found in the installation instructions. is in working order. This may cause Level the appliance with the aid of the small water stains.
Installation and connection Fresh water connection Setting hot water: 1. Open the door. 2. Switch on ON/OFF switch (. 1. Connect the fresh-water connection to the tap according to the 3. Hold down programme button # installation instructions with the and press START button ` enclosed parts.
Installation and connection Use only a residual current operated 7. Open door after approx. 4 minutes. circuit-breaker which features 8. Press START button ` until the symbol ‚. Only this extension is indicated on the digital display. guarantees compliance with 9.