Introduction Congratulation. You made a good choice buying an UES handgun of the series “HP 07”. UES hot melt products meet your highest demands regarding quality, safety and convenience in mainte- nance and operation. Through the combination of most modern automatic control engineering and control technique with a com- fortable and complete equipment the best advantages can be offered to you.
When installing, operating and maintaining the unit the safety measures referring to the main machine which the unit is built into must be taken into consideration. UES AG · Roemerstraße 15 · D-47809 Krefeld Tel.: +49 (0)2151-72950 · Fax: +49 (0)2151-7295578 · info@ues-int.net · www.ues-int.net...
Caution, possible danger of uncontrolled release/leakage of hot liquids! Disconnect power Wear full suit! plug before opening! Disconnect Use safety glasses! power supplier! Use face shield! Wear safety gloves! UES AG · Roemerstraße 15 · D-47809 Krefeld Tel.: +49 (0)2151-72950 · Fax: +49 (0)2151-7295578 · info@ues-int.net · www.ues-int.net...
The supply of hot melt exclusively takes part via a flexible hose (max. ø of the cap at the end of the hose 44 mm), which is connected with an UES hot melt system. A heater cartridge and a temperature sensor (Ni 120, PT100, NTC etc.) regulate the temperature of the handgun independent of the hose and the tank temperature.
Now switch on the system and adjust, according to the manual of hot melt systems, the temperatures which are recommended by the adhesive producer. Plug in hose connector Connection unit hose UES AG · Roemerstraße 15 · D-47809 Krefeld Tel.: +49 (0)2151-72950 · Fax: +49 (0)2151-7295578 · info@ues-int.net · www.ues-int.net...
Important! Do never hang up the handgun at the handle but always at the suspension at the top of the handgun. Contact protection Suspension UES AG · Roemerstraße 15 · D-47809 Krefeld Tel.: +49 (0)2151-72950 · Fax: +49 (0)2151-7295578 · info@ues-int.net · www.ues-int.net...
The HP07 can be provided with three different module types. As standard it is delivered with the module H300P. This module is technically based upon the UES standard module H300 so the entire UES nozzle programme for this type of module can be used.
Readjust the operating pressure and check the needle stroke. 4 mm hexagon socket screw key Stroke adjusting screw Distance between lever and housing about 0.5 to 1 mm UES AG · Roemerstraße 15 · D-47809 Krefeld Tel.: +49 (0)2151-72950 · Fax: +49 (0)2151-7295578 · info@ues-int.net · www.ues-int.net...
Clean or replace nozzles. Check glue store-container) cause, e.g. too high temperature in the tank. UES AG · Roemerstraße 15 · D-47809 Krefeld Tel.: +49 (0)2151-72950 · Fax: +49 (0)2151-7295578 · info@ues-int.net · www.ues-int.net...
The safety lever has to be put into secured position so that the cable channel is laid open and the service block with trigger and electric can be taken out of the housing. UES AG · Roemerstraße 15 · D-47809 Krefeld Tel.: +49 (0)2151-72950 · Fax: +49 (0)2151-7295578 · info@ues-int.net · www.ues-int.net...
Page 15
Electric set HP07 (UES/3000) consisting of Pos.6 Plug not shown Micro switch (optional for spraying application) Pos.14 Temperature sensor Pos.15 Heater cartridge Pos.16 Earthing cable UES AG · Roemerstraße 15 · D-47809 Krefeld Tel.: +49 (0)2151-72950 · Fax: +49 (0)2151-7295578 · info@ues-int.net · www.ues-int.net...
(e.g. 2,4m hose; UES part no. 100292) • handy appurtenance: Spray air control HP 07 – not operated grip shift switched off the air for the gun (inline micro switch) (UES article: 100493) UES AG ·...