Lux Products SMART TEMP TX1500 Installation And Operating Instructions

INSTALLATION AND OPERATING INSTRUCTIONS
TX1500b SERIES
®
SMART TEMP ELECTRONIC THERMOSTAT
UP
MO DAY
HEAT
PM DOWN
MO UP
DAY
HEAT
PM DOWN
SET SET
SATURDAY SUNDAY
PROGRAM PROGRAM RESET FAN HEAT
SET AUTO OFF
WEEKDAY FILTER
PROGRAM HOLD ON COOL
SET RUN NEXT
DAY/TIME
1500
P a t e n t s P e n d i n g
SIMPLIFIED INSTRUCTIONS
TO SET TIME & DAY • Press UP/DOWN to set time. TEMPORARY TEMPERATURE OVERRIDE
• Rotate Dial to SET •Press UP/DOWN to adjust set temperature.
DAY/TIME. TO SET PROGRAMS •To clear OVERRIDE press UP/DOWN until
• Press UP to change • Rotate Dial to SET original set temperature appears or wait for
Installs Easily
Set Day & Time
LUX PRODUCTS CORPORATION • Mt. Laurel, New Jersey 08054, USA
WARNING: Use Energizer ® or DURACELL
Energizer ® is a registered trademark of Eveready Battery Company, Inc.
DURACELL ® is a registered trademark of The Gillette Company, Inc.
Complete, Easy To Read Programming And Installation Instructions Inside
I M P O R T A N T !
Thank you for your confidence in our product. To obtain the best results from
your investment, please read these instructions and acquaint yourself with your
READ
purchase before installing your new thermostat. Then follow the installation
INSTALLATION
procedures, one step at a time. This will save you time and minimize the chance
INSTRUCTIONS
of damaging the thermostat and the systems it controls. These instructions may
contain information beyond that required for your particular installation. Please
FIRST
save for future reference.
FEATURES
• The TX1500 can
The Active Program Period
be used with
most 24 volt
Lux Speed Dial
gas, oil or electric
heating and air
conditioning
systems, single-stage
heat pumps or gas
millivolt heating
systems.
It cannot be used
with 120 volt heating
systems or multistage
heat pumps. Ask your
dealer for other LUX
thermostats to
control those
systems.
• The TX1500 is
programmable. There
are four
programming periods
Button to Light Display
per day. Each period
can be programmed separately.
• Easy to use Lux Speed Dial .
®
• You can use the built-in time/temperature programs, or alter them to suit your
schedule. The TX1500 provides separate programming for weekdays, Saturday, and
Sunday — for both heating and cooling. You can override the programmed temperatures
for as little as one programming period or for an entire vacation.
• In cool weather, when the system switch is set to HEAT, the TX1500 will maintain
cooler "set back" room temperatures to save energy. It will then change to warmer
"comfort" settings — all automatically, at specified times during the day.
• In warm weather, when the system switch is set to COOL, the TX1500 will maintain
warmer "set back" room temperatures to save energy. It will then change to cooler
"comfort" settings - all automatically, at specified times during the day.
• A large liquid crystal display shows time, day of the week, and room and set
temperatures. It will remind you when the filter should be changed in your blower.
• Temperature swing adjustment lets you fine-tune your system for maximum
comfort and economy.
• 5/2 Minute Selectable Minimum Run/Off Time for Short Cycle/Compressor Protection
• Two Energizer or DURACELL "AA" alkaline batteries (not included) are used to retain your
® ®
time and temperature program and to light the display.
Easy as
UP
MO DAY
HEAT
PM
DOWN
SET SET
SATURDAY SUNDAY RESET
PROGRAM PROGRAM FAN HEAT
AUTO
SET OFF
WEEKDAY FILTER HOLD ON
PROGRAM COOL
1–2–3
SET RUN
DAY/TIME NEXT
1500
P a t e n t s P e n d i n g
SIMPLIFIED INSTRUCTIONS
TO SET TIME & DAY • Press UP/DOWN to set time. TEMPORARY TEMPERATURE OVERRIDE
• Rotate Dial to SET •Press UP/DOWN to adjust set temperature.
DAY/TIME. TO SET PROGRAMS •To clear OVERRIDE press UP/DOWN until
• Press UP to change • Rotate Dial to SET original set temperature appears or wait for
t d WEEKDAY the start tf the next period
Choose Heat or Cool
® Alkaline Batteries Only
The Set Temperature
Liquid Crystal
®
Display
© COPYRIGHT 2006 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED
C
• Your thermostat is a precision instrument. Please handle it with care.
• Turn off electricity to the appliance before installing or servicing thermostat or any
part of the system. Do not turn electricity back on until work is completed.
• Do not short (jumper) across electric terminals at control on furnace or air
conditioner to test the system. This will damage the thermostat and void your
warranty.
• All wiring must conform to local codes and ordinances.
• This thermostat is designed for use with 24 volt and millivolt systems. The
thermostat should be limited to a maximum of 1.0 amps; higher amperage may
cause damage to the thermostat. If you are in doubt, call your utility company.
INSTALLATION
Please read all instructions carefully
52017
before beginning installation.
TOOLS REQUIRED
#1 Phillips screwdriver (small)
Drill with 3/16-in. (4.8mm) bit
THERMOSTAT LOCATION
On replacement installations, mount
the new thermostat in place of the old
one unless the conditions listed below suggest otherwise. On new installations, follow
the guidelines listed below.
1. Locate the thermostat on an inside wall, about 5 ft. (1.5m) above the floor, and in a
room that is used often.
2. Do not install it where there are unusual heating conditions, such as: in direct
sunlight; near a lamp, radio, television, radiator, register, or fireplace; near hot water
pipes in a wall; near a stove on the other side of a wall.
3. Do not locate in unusual cooling conditions, such as: on a wall separating an
unheated room; or in a draft from a stairwell, door, or window.
4. Do not locate in a damp area. This can lead to corrosion that will shorten
thermostat life.
5. Do not locate where air circulation is poor, such as: in a corner or an alcove; or
behind an open door.
6. Do not install the unit until all construction work and painting has been completed.
Thermostat
Body
7. This thermostat does not require leveling.
System
Switch
Fan Switch
REMOVING THE OLD THERMOSTAT
Switch electricity to the furnace and air conditioner OFF;
Easy to
then proceed with the following steps.
follow
instructions
Thermostat
Cover
2. Note the letters printed near the terminals. Attach labels
(enclosed) to each wire for identification. Remove and label
wires one at a time. Make sure the wires do not fall back inside the wall.
3. Loosen all screws on the old thermostat and remove it from the wall.
MOUNTING THE TX1500 ON THE WALL
3. Press up on the button on bottom of thermostat
and swing the body away from the base and up
to remove the body from the base.
Be careful not to drop the body or disturb electronic parts.
Leave the cover closed while the body is being removed from the base.
A U T
C A U T I O N
To avoid electrical shock and
to prevent damage to the
furnace, air conditioner, and
thermostat, disconnect the power
supply before beginning work. This
can be done at the fuse box, at the
circuit breaker, or at the appliance.
1. Remove cover from old
thermostat. Most are snap-on
types and simply pull off. Some
have locking screws on the
side. These must be loosened.
1. Strip insulation
3/8 in. (9.5mm)
from wire ends
and clean off
any corrosion.
C A U T I
I O N
OFF
C A U T I O N
Read instructions carefully
before removing any
wiring from existing
thermostat. Wires must be
labeled before they are
removed. When removing
wires from their terminals,
ignore the color of the
wires since these may not
comply with the standard.
2. Fill wall opening with
non-combustible
insulation to prevent
drafts from affecting
the thermostat.
O N