Sony DVP-NS705V Service Manual page 42

Disc Type
1. Disc Type Auto Check
2. DVD SL 12cm
3. DVD DL 12cm
4. CD 12cm
5. SACD 12cm
6. DVD SL 8cm
7. DVD DL 8cm
8. CD 8cm
9. LCD 8cm
0. Reset SLED TILT
TC. --:--:-- EMG.00
CD 12cm
Display when CD 12cm disc was selected
[0]
Reset SLED TILT Reset the Sled and Tilt to initial
position.(This model does not have Tilt
device, so reset only the Sled to initial
position.)
[1]
Disc Type Check Judge automatically the loaded disc. As
the judged result is displayed at the bot-
tom of screen, make sure that it is cor-
rect.
If Disc Check Memory menu has not
been executed after EEPROM default
setting, the disc type cannot be judged.
In this case, return to the initial menu
and make a check for three types of
discs (SL, DL, CD).
[2] [9]
to Select the loaded disc. The adjusted
value is written to the address of se-
lected disc. No further entry is neces-
sary if
2. Servo Control
Servo Control
1. LD Off R. Sled FWD
2. SP Off L. Sled REV
3. Focus Off
4. TRK. Off
5. Sled Off
6. CLVA Off
7. FCS. Srch Off
0. Reset SLED TILT
SA.------ SI.-- EMG. 00
DVD SL 12 cm
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
[0]
Reset SLED TILT Reset the Sled and Tilt to initial
position.(This model does not have Tilt
device, so reset only the Sled to initial
position.)
[1]
LD Turn ON/OFF the laser.
[2]
SP Turn ON/OFF the spindle.
[1]
was selected.
[3]
Focus
[4]
TRK
[5]
Sled
[6]
CLVA
[7]
FCS. Srch
→ Sled FWD
← Sled REV
3. Track/Layer Jump
Tracking/Layer Jump
R. Fj (L1 → L0)
1. 1Tj FWD
L. Fj (L0 → L1)
2. 1Tj REV
U. Lj (L1 → L0)
3. 2Tj FWD
D. Lj (L0 → L1)
4. 2Tj REV
5. NTj FWD
6. NTj REV
7. 500Tj FWD
8. 500Tj REV
9. 10k/20k FWD
0. 10k/20k REV
SA.------ SI.-- EMG. 00
DVD SL 12 cm
On this screen, track jump, etc. can be performed. Only for the
DVD-DL, the focus jump and layer jump are displayed in the right
field.
[1]
1Tj FWD
[2]
1Tj REV
[3]
2Tj FWD
[4]
2Tj REV
[5]
NTj FWD
[6]
NTj REV
[7]
500Tj FWD
[8]
500Tj REV
[9]
10k/20k FWD
[0]
10k/20k REV
– The following commands are valid for DVD-DL disc only –
→ Fj (L1 → L0)
6-9
Search the focus and turn on the focus.
Turn ON/OFF the tracking servo.
Turn ON/OFF the sled servo.
If PLL is not locked (or can not be
locked), the sled servo does not be
turned ON. (Indication remains as OFF)
Turn ON/OFF normal servo of spindle
servo.
Apply same voltage as that of focus
search to the focus drive to check the
focus drive system.
Move the sled outward. Perform this
operation with the tracking servo turned
off.
Move the sled inward. Perform this op-
eration with the tracking servo turned
off.
1-track jump forward.
1-track jump reverse.
2-track jump forward.
2-track jump reverse.
N-track jump forward.
N-track jump reverse.
Fine search forward.
Fine search reverse.
Direct search forward.
Direct search reverse.
Focus jump forward.
(Trk/Sled Servo OFF)