Pressure Washer Operator’s Manual This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101-2010 (Testing and Rating Performance of Pressure Washers). BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC MILWAUKEE, WISCONSIN, U.S.A. Manual No. 317389GS Revision -...
Page 2
You never have to look far to find Victa support and service for your pressure washer. There are many authorized service dealers who provide quality service. You can also contact Victa Customer Service by phone at 1800 356 632, or on the Internet at www.victa.com.au or BRIGGSandSTRATTON.COM.
• Read all instructions with mask so you are certain the mask will provide the necessary protection against inhaling harmful Fire Explosion Kickback Projectile vapors when using chemicals. Moving Parts Flying Objects Chemical Burn Hot Surface www.victa.com.au...
Page 5
WARNING Exhaust heat/gases could ignite WARNING Fuel and its vapors are extremely flammable combustibles, structures or damage fuel and explosive which could cause burns, tank causing a fire, resulting in death, fire or explosion resulting in death, serious injury and/or property damage. serious injury and/or property damage.
Page 6
Power Products authorized parts ONLY. If equipment is used with caught in the starter or other rotating parts. parts that DO NOT comply with minimum specifications, user assumes all risks and liabilities. • Tie up long hair and remove jewelry. www.victa.com.au...
Assembly Attach Handle and Accessory Tray 1. Place handle (A) onto handle supports (B) connected to Read entire operator’s manual before you attempt main unit. Make sure holes (C) in handle align with to assemble or operate your new pressure washer. holes (C) on handle supports.
If you experience starting or performance problems after using fuel, switch to a different fuel provider or change brands. This engine is certified to operate on gasoline. The emission control system for this engine is EM (Engine Modifications). www.victa.com.au...
Lubricate O-Rings Lubricate all connections shown below, following these instructions: Lubrication of o-rings is extremely important for installation 1. Inspect and clean connecting surfaces prior to and operation. The use of a lubricant (petroleum or synthetic lubrication and assembly. grease) during assembly helps seat o-rings properly and provides an improved seal.
4. Attach garden hose adapter (B) to water inlet. Tighten by hand. 5. Run water through your garden hose for 30 seconds to clean out any debris. NOTICE DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 38°C (100°F)). www.victa.com.au...
Features and Controls Read this Operator’s Manual and safety rules before operating your pressure washer. Compare the illustrations with your pressure washer, to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. A - Spray Gun — Controls the application of water onto L - Automatic Cool Down System —...
WARNING Exhaust heat/gases could ignite combustibles, structures or damage fuel tank causing a fire, resulting in death, serious injury and/or property damage. • Keep at least 1.5 m (5 ft) clearance on all sides of pressure washer including overhead. www.victa.com.au...
Page 13
8. Move throttle lever (A) to the Fast position, shown as a WARNING Starter cord kickback (rapid retraction) will rabbit pull hand and arm toward engine faster than you can let go which could cause broken bones, fractures, bruises, or sprains resulting in serious injury.
4. Hang high pressure hose on hook attached to accessory tray on front of tray, as shown. Usage Tips • For most effective cleaning, keep spray tip from 20 to 61 cm (8 to 24 in) away from cleaning surface. www.victa.com.au...
• If you get spray tip too close, especially using a high Pressure Washer Rinsing pressure spray tip, you may damage surface being For Rinsing: cleaned. 1. Remove black soap spray tip from nozzle extension. • DO NOT get closer than 15 cm (6 in) when cleaning tires. 2.
Examine the screen on the pump’s water inlet. Clean it if the 1800 356 632 for assistance. screen is clogged or replace it if screen is damaged. Some adjustments will need to be made periodically to properly maintain your pressure washer. www.victa.com.au...
Page 17
Check High Pressure Hose 5. Slowly push down until you feel the ball move slightly, push no more than 3 cm (1/8 in). Slight pressure may The high pressure hose can develop leaks from wear, be required to free the ball. kinking, or abuse.
• If over the FULL mark on dipstick, drain oil to reduce oil level to Outdoor temperatures determine the proper oil viscosity for FULL mark on dipstick. the engine. Use the chart to select the best viscosity for the outdoor temperature range expected. 4. Replace and tighten dipstick. www.victa.com.au...
Page 19
Changing Engine Oil 2. Carefully remove air cleaner to prevent debris from falling into carburetor. If you are using your pressure washer under extremely dirty 3. Wash foam air cleaner (C) in liquid detergent and or dusty conditions, or in extremely hot weather, change the water.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK • Store away from furnaces, stoves, water heaters, clothes dryers, or other appliances that have pilot light or other ignition source because they could ignite fuel vapors. www.victa.com.au...
Winter Storage Change Engine Oil While engine is still warm, drain oil from crankcase. Refill with recommended grade. See Changing Engine Oil in Engine NOTICE You must protect your unit from freezing Maintenance. temperatures. • Failure to do so will permanently damage your pump and render Protecting the Pump your unit inoperable.
6. Bad spark plug. 6. Replace spark plug. 7. Water in fuel. 7. Drain fuel tank; fill with fresh fuel. 8. Excessively rich fuel mixture. 8. Contact local service facility. Engine lacks power. Dirty air filter. Replace air filter. www.victa.com.au...
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC PRESSURE WASHER OWNER WARRANTY POLICY Effective April 1, 2012; replaces all undated Warranties and all Warranties dated before April 1, 2012. LIMITED WARRANTY Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship or both.
* This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101- 2010 (Testing and Rating Performance of Pressure Washers). Briggs & Stratton Power Products Group, LLC P.O. Box 702 Milwaukee, Wisconsin, 53201-0702 U.S.A. 1800 356 632 www.victa.com.au...
Need help?
Do you have a question about the 2500 PSI and is the answer not in the manual?
Questions and answers