Table of Contents
Advertisement
How to install and operate the
X-program amplifiers
X-A10
X-A20
X-A30
X-A40
Welcome!
This owners manual is written in easy english and
uses a lot of drawings to simply the installation and
use of the above amplifiers.
Your X-program amplifiers must be installed
correctly in order to work well. This manual will show
you how to install the amplifier like a pro. Please
read the entire manual before beginning the
installation.Install the amplifier yourself if you feel
confident with our instructions and if you have the
proper tools. However if you feel unsure, turn over
the installation job to someone better suited to it.
Warranty Service
This amplifier is covered by warranty, depending
on the conditions in the country where it is sold. If
the amplifier is returned for service, please include
the original dated receipt with the product.
Technical Assistance
For technical assistance ask the shop where the
product was sold or the distributor in your very coun-
try. Information can also be found on our WEB-site
www.xprogram.com
We follow a policy of continuous advancement in
development. For this reason all or part of
specifications & designs may be changed without
prior notice.
DECLARATION OF CONFORMITY
X-program amplifiers for vehicles are manufactured
in accordance with the EU directive EEC 95/54 (72/
245/EEC) and are marked with the approval number.
They are also marked in accordance with the WEEE-
directive 2002/96/EC.
The products are also produced in accordance with
the EU RoHS directive 2002/95/EC.
Contents
Features...................................
Installation................................
Tools and materials needed..........
Amplifier installation kit................
Routing Wires............................
Power and Outputs.....................
Inputs and controls.....................
High and low level inputs...............
Input level control...........................
Crossovers, etc..............................
Features on each model ...............
X-A10 speaker wiring:
Subwoofer.................................
X-A20 speaker wiring:
Front speakers............................
Subwoofer.................................
Two speakers and subwoofer..........
Four speakers............................
Testing......................................
Troubleshooting...........................
Professional tips..........................
Specifications.............................. 14
This product must be returned to the
separate collection system for electronic
products. Do not dispose this product
together with general household waste.
X-program is designed, engineered and distributed by:
P.O. Box 13029 - SE-40251 Göteborg - Sweden
Tel: +46 31 840060 - Fax: +46 31 844021
E-mail: info@dls.se
www.xprogram.com
X-program products are produced in Taiwan
2
2
3
3
3
4
5
5
6
6
6-7
8
9
9
10
11
12
12
13
Advertisement
Table of Contents
Related Manuals for X-PROGRAM X-A10
Summary of Contents for X-PROGRAM X-A10
-
Page 1: Table Of Contents
Do not dispose this product specifications & designs may be changed without together with general household waste. prior notice. X-program is designed, engineered and distributed by: DECLARATION OF CONFORMITY X-program amplifiers for vehicles are manufactured DLS Svenska AB in accordance with the EU directive EEC 95/54 (72/ P.O. -
Page 2: Features
Do not mount the amplifier in an inverted or upside down position. X-A10 has a cooling fan built-in, make sure that the air can circulate freely around the fan opening. Check all locations and placements carefully before making any cuts, drilling any holes or making any connections. -
Page 3: Tools And Materials Needed
Tools and material needed Routing wires Tools: Flat and Phillips screwdrivers Wire cutter Wire stripper Electric drill with drills Crimping tool Digital multimeter or test lamp Wire brush, scraper or a piece of an abrasive sheet to remove paint for a good ground connection Grease to protect the ground Stereo connection from oxidation... -
Page 4: Wiring
Wiring Power and Outputs Remote terminal ( REM ) Power terminal ( +12V) For RCA cable signal input: Connect the radio power antenna lead = remote Connect the fuse holder as close to the vehicle turn on/off from the car stereo to the amplifier remote battery + as possible, using AWG 4 /5 = 21 / 16 connection. -
Page 5: Inputs And Controls
Use either the low level or high level input, do not use both at same time. X-A10/20/30 On these models you connect as in this example: Low level input Use a pair of shielded stereo audio cables with RCA High Input type jack. -
Page 6: Input Level Control
Crossovers/filters and other features on each model Input Level control The input level control, 5V – 0,25 V, X-A10 is a mono channel amplifier mainly matches the output of your radio to intended for use with one or two subwoofers but can the input of the amplifier. - Page 7 Crossovers/filters and other features on each model...
-
Page 8: Subwoofer
X-A10 Speaker wiring X-A10 Single 4 ohm subwoofer Two 4 ohm subwoofers NOTE! The speaker terminal has dual + and - terminals for easier connection if you have more 4/2 ohm than one sub- 4 ohm woofer. They are internally conn-... -
Page 9: Subwoofer
X-A20 Speaker wiring X-A20 Two fullrange One 4 ohm speakers to subwoofer channel R / L bridged 4 ohm NOTE! Minimum speaker impedance in bridged connection is 4 ohm, this connection gives a 2 ohm load with a 4 ohm subwoofer. The load is halved when NOTE! connected in bridge mode. -
Page 10: X-A30 Speaker Wiring: Two Speakers And Subwoofer
X-A30 Speaker wiring X-A30 1. Two fullrange speakers to the front channels One or two subwoofers to sub channels, Each speaker min 4 ohm. 4 ohm 4 ohm Connect to the lower terminals for SUB CH + and -. Connect to the upper terminals for FR CH and FL CH. -
Page 11: Front Speakers
X-A40 Speaker wiring X-A40 1. Four fullrange speakers to X-A40. One pair 2. Two fullrange speakers and one subwoofer in front and one pair in rear. bridged to X-A40. 4 ohm Rear speakers Subwoofer in bridge mode to channel RL- / RR+ Front speakers Rear or front stereo speakers Front and rear stereo speakers... -
Page 12: Testing
Testing Troubleshooting Before you finish the installation, you should do the If problems occour during the installation, or later, following tests to make sure the wiring is correct and this guide might help you to find out whats´s wrong. everything is operating properly. THE AMPLIFIER IS DEAD: 1. -
Page 13: Professional Tips
Professional Tip: Professional Tip: NOISE PROBLEMS SPEAKER POLARITY CHECK. WHINING NOISE VARYING WITH ENGINE All speakers in a car audio system should be REVOLUTIONS: connected in phase (the same polarity). All spea- ker cones must move in the same direction. Out of Do this: phase speakers will cause a lack of bass, and a Rewire the power supply (12 V) to source... -
Page 14: Specifications
Specifications X-program X-A10 X-A20 Number of channels Amplifier class Power output, 4 ohm (0,1% THD) 200 W 2 x 50 W All above output power Power output, 2 ohm (0,2% THD) 300 W 2 x 70 W ratings at 14,4 VDC... -
Page 16: Dls Svenska Ab
DLS Svenska AB P.O. Box 13029 SE-40251 Göteborg, Sweden Tel: +46 31 840060 Fax: +46 31 844021 E-mail: info@dls.se www.dls.se...
Need help?
Do you have a question about the X-A10 and is the answer not in the manual?
Questions and answers