Sanyo DC-D9 Instruction Manual page 7

Notes on handling compact discs
Do not expose the disc to direct sunlight, high humidity or high
temperatures for extended periods of time.
Discs should be returned to their cases after use.
Do not apply paper or write anything on the disc surface.
Handle the disc by its edge. Do not touch the playing surface (glossy
side).
Fingerprints and dust should be carefully wiped off the playing surface
of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
- Never use chemicals such as record cleaning sprays, antistatic
sprays or fluids, benzene or thinner to clean compact discs.
Temporarily stopping play
Press the PLAY/PAUSE button. " D" blinks on the display. To resume
play, press the button again.
Skip play
To skip to track 6 while track 3 is playing, press the -/ W button
repeatedly until "6' appears in TRACK on the display.
To skip back to track 3 while track 6 is playing, press the 14< /<< button
repeatedly until"3 appears.
The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press O, then 6.
Search (forward/reverse)
If the >/ EM or ~< /<4 button is pressed during play, the player will
search at high speed in the forward or reverse direction while the button
is being pressed. When the button is released, normal play will continue.
Random play
Press the RANDOM button on the remote control to begin random play.
The player will automatically select and play discs and tracks at random.
"RANDOM appears on the display.
If the RANDOM button is pressed during random play, the player will
select the next random track.
Random play will not function during programmed play.
Repeat play
Press the REPEAT button repeatedly to select the desired repeat mode
in the following sequence. The selected repeat mode is shown on the
display.
REPEAT: Repeat all tracks on the selected disc.
REPEAT CONT: Repeat all tracks on all discs.
Released: Normal play mode
Note:
During programmed play, only "REPEAT" can be selected.
Changing discs during play
While the player is playing one disc, press one of the DISC buttons to skip
to another disc. "CH dlSC blinks for a few seconds, then the selected disc
moves into playing position.
Play starts automatically from the first track on the disc.
PROGRAMMED PLAY
Up to 24 selections, from up to 3 discs, can be programmed for play in any
order.
To begin the programming procedure, select "CD function first.
The discs or tracks must be programmed in the stop mode.
- The same disc or track can be programmed more than once.
Load discs that you want to programme before starting programmed
play.
Follow the example below to programme tracks 2 and 6 on DISC 1 and all
tracks on DISC 3. In this example, each disc has 9 tracks and DISC 3 is
in playing position.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Press the MEMORY button.
Select disc 1 by pressing the DISC 1 button.
The DISC SELECT button on the remote control can also be used.
Select track 2 by pressing the >/ ›~ button.
The number buttons on the remote control can also be used.
Press the MEMORY button. "PROG." remains lit.
Select track 6 by pressing the FF/ FM button.
Press the MEMORY button. "PROG." remains lit.
Select disc 3 by pressing the DISC 3 button.
Press the MEMORY button. "PROG." remains lit
Press the PLAY/PAUSE button to stari play.
When all programmed selections have played, the player stops
automatically. "O 0.00 appears on the display.
The programme contents are retained in memory.
Any attempt to programme more than 24 selections will result in
"FULL" being displayed and discontinuation of the programming.
The programme is cleared in the following cases:
When the STOP button is pressed in the stop mode
When the OPEN/CLOSE button is pressed
-6-