Before Operation - Sanyo DC-D9 Instruction Manual

BEFORE OPERATION
Turning the power on and off
Press the POWER button. The displays light and the STANDBY Indicator
goes out. (After connecting the mains lead, when you press the POWER
button for the first time, the volume reset feature automatically sets the
initial volume level "Vo 3.)
To turn off the power, press the POWER button again. The STANDBY
indicator lights.
When the mains lead is connected to the AC outlet, the STANDBY
indicator lights and the unit will respond to commands from the remote
control.
Selecting the function
Press the FUNCTION button to select the desired function. Each time the
button is pressed, the display changes as follows:
Cd (CD) — TA (Tape) — TU (Tuner) — Vd (Video) —
Cd(CD) —...
The function is automatically selected when CD play is started or when the
BAND button has been pressed (except during recording or tape dub-
bing).
When the function selection is changed, CD play is automatically
stopped.
Adjusting the volume
Press the" ~" or" ~" portion of the VOLUME button, or press the "+" or
" " VOLUME button on the remote control. The volume level appears on
—
the display (Vo 0- Vo 10).
Adjusting the Ieft.lright speaker balance
Use the BALANCE control to adjust the Iefthight speaker balance.
Adjusting the sound quality
Use the TREBLE or Ml D control to adjust the treble or mid range output
level.
Bass expander system
Use the BASSXPANDER control to adjust the bass output level.
1
WHAT TO DO IF ...
If the operation of the unit or display is not normal or when all the
memory contents are to be cleared, disconnect the mains lead from the
] ACoutlet,thenpressthe RESETbution(rearoftheunit)for2Oseconds
or more.
f
\
RESET
%
/
I
CD PLAY
Use compact discs bearing the symbol shown below. In addition to
conventional 12 cm CDs, this system can be used to play 8 cm CDs without
an adapter.
tiT3!
DIGITAL AUDIO
Note:
Do not touch the disc tray while it is moving.
Never place anything except a compact disc on the disc tray. Foreign
objects can damage the unit.
Do not apply excessive force to the disc tray.
Discs must be placed on the disc tray one at a time.
1. Select "CD" function by pressing the FUNCTION button. "Cd appears
on the display, then "Cd is replaced by "dlSC."1" disc number blinks.
2. Press one of the DISC buttons (1, 2 or 3), then press the OPEN/
CLOSE button.
If the DISC button which "no disc" has been detected by the
changer mechanism is pressed, that disc tray slides out automati-
cally.
The selected disc number blinks and the selected disc tray slides out.
"OPEN" appears on the display.
3. Place the disc with the label facing upon the disc tray.
5. Repeat steps 2-4 to load another disc.
6. Press one of the DISC buttons (1, 2 or 3).
g
,Rl,
0.01
D
*
"D" appears, and play starts from the first track of the selected disc.
The track number and elapsed play time for the current track are
displayed.
If the desired disc number has been selected, the PLAY/PAUSE
button can also be used to start play.
Note:
If the disc is loaded with the label facing downward, or if a badly
scratched disc is loaded, "NO dlSC appears on the display.
If this occurs, load the disc correctly or replace the damage disc.
7. Press the STOP button to end disc play.
When the last track of the last disc has been played, the player stops
automatically.
When the OPEN/CLOSE button is pressed during play, play will stop
and the disc tray will slide out.
Ejecting discs
1. While in the CD play or stop mode, press one of the DISC buttons to
be ejected, then press the OPEN/CLOSE button.
While the player is playing one disc, you can eject another disc
without stopping play.
2. Remove the disc.
For 12 cm CD
For 8 cm CD
4. Press the OPEN/CLOSE button again to close the disc tray
-5-