Declaration Of The Manufacturer; Quick Start - NEC AccuSync LCD193WM User Manual

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S
POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage
within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any
kind of contact with any part inside this unit.
This symbol alerts the user that important literature
concerning the operation and maintenance of this
unit has been included. Therefore, it should be read
carefully in order to avoid any problems.
Contents
Power
User's
Cable Holder
Cord
Manual
Audio
Video Signal
Cable
Cable

Quick Start

Cable Holder
Base
Figure S.1
Figure A.1
Macintosh Cable
Adapter (not included)
Power Cord
Figure B.1
01_English
WARNING
CD-ROM
Base AccuSync LCD monitor
Stand (base stand not connected)
Stand
Locking Tabs
Figure A.2
Audio Input
Input (D-Sub)
Cable holder
Connect to Computer
audio output
English-1
1

Declaration of the Manufacturer

We hereby certify that the colour monitor AccuSync LCD193WM
(L196H5)/AccuSync LCD203WM (L206H6)/AccuSync LCD223WM
(L226H7) are in compliance with
Council Directive 73/23/EEC:
– EN 60950-1
Council Directive 89/336/EEC:
– EN 55022
– EN 61000-3-2
– EN 61000-3-3
– EN 55024
Your new NEC AccuSync LCD monitor box* should contain the
following:
• AccuSync LCD monitor with tilt base
• Audio Cable
• Power Cord
• Video Signal Cable
• User's Manual
• CD-ROM
• Base Stand
• Cable Holder
* Remember to save your original box and packing material to
transport or ship the monitor.
To attach the Base to the LCD Stand:
1. Attach the Base to the Stand. The locking tabs on the Stand should
fit into the hole on the centre back of the Base (Figure S.1).
To attach the Cable Holder:
1. Insert the tabs of Cable Holder into the hole of Stand and slide the
Cable Holder downward into place (Figure S.1).
NOTE: Please confirm that the tabs are completely secure.
To attach the AccuSync LCD monitor to your system, follow these
instructions:
1. Turn off the power to your computer.
2. For the PC with Analog output: Connect the 15-pin mini D-SUB
signal cable to the connector of the display card in your system
(Figure A.1). Tighten all screws.
For the Mac: Connect the MultiSync Macintosh cable adapter (not
included) to the computer. Attach the 15-pin mini D-SUB signal
cable to the MultiSync Macintosh cable adapter (Figure A.2).
Tighten all screws.
NOTE: Some Macintosh systems do not require a Macintosh cable
adapter.
3. Connect the 15-pin mini D-SUB of the video signal cable and
Audio Cable to the appropriate connector on the back of the
monitor (Figure B.1). Connect the Headphone (not included) to
the appropriate connector at the front of the monitor (Figure C.1).
4. Connect one end of the power cord to the monitor and the other
end to the power outlet. Place the Video Signal Cable and power
cord to the Cable holder (Figure B.1).
NOTE: Adjust position of cable that place under the Cable holder to
avoid damage for cable or monitor.
NOTE: Please refer to Caution section of this manual for proper
selection of power cord.
16/2/07, 8:01 AM
and marked with
NEC Display Solutions, Ltd.
4-13-23, Shibaura,
Minato-Ku
Tokyo 108-0023, Japan