media-tech MT4050 User Manual

media-tech MT4050 User Manual

Indoor securecam 300k

Advertisement

INDOOR
SECURECAM
300K
MT4050
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MT4050 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for media-tech MT4050

  • Page 1 INDOOR SECURECAM 300K MT4050 User Manual...
  • Page 2: Table Of Contents

    Index Alarm Settings ������������������������������������������������������������������������������������������10 Alarm service setting ����������������������������������������������������������������������������������� 10 Mail Service Setting �������������������������������������������������������������������������������������� 11 Notice ������������������������������������������������������������������������������������������������������������ 3 FTP Service Setting ��������������������������������������������������������������������������������������� 11 Product introduction 3 Alarm log ���������������������������������������������������������������������������������������������������������� 12 Product summary �������������������������������������������������������������������������������������� 3 User and device setting�������������������������������������������������������������������������12 Main features ���������������������������������������������������������������������������������������������� 3 Multi-device Setting �������������������������������������������������������������������������������������...
  • Page 3: Notice

    Product introduction Notice ■ Keep away from the places for high-temperature, heat source and Product summary direct sunlight; ■ Keep away from water and when get wet, cut off the power im- Thank you for choosing our securecam camera series, the mediately�...
  • Page 4: Package For Typical Production

    Package for typical production Notice: Please check carefully if all listed items are included in the pack- ■ Power adaptor, ■ CD, ■ Cable, ■ Bracket L, ■ Antenna age, if anything missing, please contact your vendor� Overview The camera adopts 300K pixels CMOS sensor, 3�6mm lens, built in PTZ and MIC, 8 IR LEDs, audio out socket� It uses 5V power adaptor�...
  • Page 5: Wired Connection To Lan

    Power on the IP camera, connect IP camera to router by network cable, meanwhile, connect computer to the same router� MT4050 Router Insert CD to computer driver, double click “LSearch_en�exe” in the CD, run the software, click “Search”, select the device searched (this process may take up to 5min), click “Browse”...
  • Page 6: Connecting Camera To Local Wifi

    Connecting camera to local WiFi You can connect the camera to your local router by wire- less connection� MT4050 Notice: When the device is connected both WiFi and wired, Click the “Scan” button, it will show you all detected wire- less networks�...
  • Page 7: Connecting Camera To Internet Network

    Connecting camera to Internet network You should connect WiFi router to WAN (ADSL modem or other router with internet access) as shown below� If you want to access your IP camera from WAN (when you do not have access to local network), you must make a port forwarding on the router�...
  • Page 8: Operation Of Ie Browser

    Operation of IE browser Record – you can start recording video (it requires prior definition of storage in one of PC computers in local net- work)� View video Snapshot - you can save snapshot (web browser will enter After installing the plug-ins, click “Mode 1 to view” to view snapshot in new window)�...
  • Page 9: Device Information

    Note: IR button can control work mode of IR LED� IR LED Remark: Please carefully check the camera time, so it can may have auto, forced close two mode, the IR LED will pow- be sure the alarm accuracy� er on or off according to environment light in auto mode; Local recording path the IR LED always power off in forced close mode�...
  • Page 10: Alarm Settings

    UPnP settings Remark: The router connected to camera need to enable DHCP when the user uses “obtain IP from DHCP server”; the If you enable UPnP, once the IP camera is connected into routers enable DHCP by default� the LAN, it will communicate with the router in the LAN and do the port-forwarding with open port of router au- Manufacture’s DDNS setting tomatically�...
  • Page 11: Mail Service Setting

    ■ Send the snap to the FTP server, user can also set the interval time between two pictures� Device only triggers alarm when it detects any motion in armed time� User can set schedule time to be “all the time”, also assign the armed time�...
  • Page 12: Alarm Log

    Alarm log User Settings You can inquire when the device performs alarm in alarm log� PTZ settings User and device setting Multi-device Setting User can add maximum 9 devices to view video simultane- ously� Click “refresh” button to check the device in the LAN� Note: When you set cruise turns all the time, the camera When click a device, will popup setting dialogue and enter will automatically stop after cruising one hour�...
  • Page 13: Visiting Device By Other Software

    CD, or download the latest software (you can find it at Google Play “iSmartViewPro”)� Due to continuous development specification and appearance of product are subject to change without prior notice. For techni- cal support please visit www.media-tech.eu.

Table of Contents