Advertisement
Advertisement
Table of Contents
Related Manuals for Behringer EURORACK MX802A
Summary of Contents for Behringer EURORACK MX802A
- Page 1 User’s Manual Bedienungsanleitung...
- Page 2 EC-Declaration of Conformity INTERNATIONAL GmbH acc. to the Directives 89/336/EWG and 73/23/EWG BEHRINGER INTERNATIONAL GmbH Hanns-Martin-Schleyer-Straße 36-38 D - 47877 Willich Name and address of the manufacturer or the introducer of the product on the market who is established in the EC...
-
Page 3: Safety Instructions
SAFETY INSTRUCTIONS DETAILED SAFETY INSTRUCTIONS: Retain Instructions: Heed Warnings: Follow instructions: Water and Moisture: Ventilation: Heat: Power Source: Grounding or Polarization: Power-Cord Protection: Cleaning: Non-use Periods: Object and Liquid Entry: Damage Requiring Service: Servicing:... - Page 4 MX802A Ultra-low noise 8-Channel Mic/Line Mixer...
- Page 5 FOREWORD...
-
Page 6: Table Of Contents
TABLE OF CONTENTS 1. INTRODUCTION ........................7 2. MONO INPUT CHANNEL ......................8 3. STEREO INPUT CHANNEL ..................... 9 4. MAIN SECTION ........................9 5. SETTING UP .......................... 11 6. CONNECTIONS ........................13 7. APPENDIX ..........................15 8. WARRANTY .......................... 18... -
Page 7: Introduction
1.2 Before you begin 1.2.1 PSU (Power Supply Unit) Connect only the provided BEHRINGER power supply unit to the MX802A. Do not connect the PSU to the EURORACK while the PSU is connected to the mains supply. The correct starting sequence is: connect mixer and PSU and then connect the PSU to the mains. -
Page 8: Mono Input Channel
1.2.2 Warranty 1.2.3 Packing If the unit is damaged, please do not return it to us, but notify your dealer and the shipping company immediately, otherwise claims for damage or replacement may not be granted. Shipping claims must be made by the consignee. 2. -
Page 9: Stereo Input Channel
2.4 Fading and panning 3. STEREO INPUT CHANNEL 3.1 Input level setting 3.2 Equalizer 3.3 Aux Sends 3.4 Volume control and panning/balancing 4. MAIN SECTION 4.1 Aux Sends... - Page 10 4.2 Stereo Aux-Returns When using Aux Send 1 as a second (pre-fader) effects send and Aux Return 2 as the effect input, do not engage “FX TO AUX 1” . The connection from Aux Return 2 to Aux Send 1 could cause feedback.
-
Page 11: Setting Up
5. SETTING UP 5.1 Desk normalization 5.2 Selecting inputs The Mic inputs are more sensitive than the Line inputs. Do not connect mics with Phantom Power switched on. Never use unbalanced mic cables with the Phantom Power switched on ever! Shorting the +48 V to earth can cause serious damage. IN / OUT Output Input... - Page 12 5.4 Auditioning a signal and setting up a channel 5.5 Recording levels 5.6 Modification Mono Channel Aux Send 2 > pre-fader...
-
Page 13: Connections
Modification on Mono Channels Add a ´pre´ link Cut the ´post´ track POST POST Before After 6. CONNECTIONS Fig. 6.1: Headphone connection Output Cable Input Ground Pin 1 Shield (+) Signal + Hum Pin 2 = (+) Signal Positive (+)Hum + Signal (-) Signal + Hum Pin 3 = (-) Signal Negative... - Page 14 Care should be taken NOT to plug mics into the console (or stagebox) while the phantom power is on. Also, mute the monitor/PA speakers when turning phantom power on or off. Allow the system to adjust for a couple of seconds after engaging phantom power before setting input gains.
-
Page 15: Appendix
Physical BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may differ from those listed or... - Page 16 7.2 Front & back views...
- Page 17 7.3 Block diagram...
-
Page 18: Warranty
BEHRINGER GmbH. BEHRINGER, ULTRAPATCH and EURORACK are a registered trademarks. ALL RIGHTS RESERVED © 1998 BEHRINGER. BEHRINGER INTERNATIONAL GmbH, Hanns-Martin-Schleyer-Str. 36-38, D-47877 Willich-Münchheide II...