Table of Contents
Advertisement
ENGLISH
Labels on tool
:
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Wear safety glasses or goggles when operating this
tool.
Wear ear protection when operating this tool.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Using an extension cable
If an extension cable is requred, use an approved extension
cable suitable for the power input of this tool (see technical
data). The minimum conductor size is 1.5 mm
When using a cable reel, always unwind the cable completely.
Also refer to the table below.
)
Conductor size (mm
2
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Features
This tool includes some or all of the following features.
6
.
2
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5 15 25 30 45 60
Cable rating (Amperes)
6
6
6
6
6 10
6
6
6
6
15 15
6
6
10
15 20 20
10 10 15
20 20 25
15 15 20
25 25
-
20 20 25
-
-
-
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
10 15
10 10 10
10 15 15
15 15 15
15 20 20
20 20 20
20 25
-
1. Variable speed switch
2. Lock-on button
3. Forward/reverse switch (only for BDEL503)
4. Mode selector (only for BDEL503)
5. Tool holder
6. Side handle
7. Depth stop
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle
Turn the grip counterclockwise until you can slide the side
u
handle (6) onto the front of the tool.
Rotate the side handle into the desired position.
u
Tighten the side handle by turning the grip clockwise.
u
Warning! Alaways use the tool with the side handle
properly assembled.
Fitting an accessory (fig.A)
Clean and grease the shank (8) of the accessory.
u
Pull back the sleeve (9) and insert the shank into the tool
u
holder (5).
Push the accessory down and turn it slightly until it fits into
u
the slots.
Pull on the accessory to check if it is properly locked. The
u
hammering function requires the accessory to be able to
move axially several centimetres when locked in the tool
holder.
To remove the accessory, pull back the sleeve (9) and pull
u
out the accessory. tool holder.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Selecting the operating mode (fig. B)
The tool can be used in three operating modes. Press in the
button (10) and rotate the drilling mode selector (4) towards
the required position, as indicated by the symbols.
Drilling
For drilling in steel, wood and plastics, set the operating
u
mode selector (4) to the
Hammer
Drilling
For hammer drilling in masonry and concrete, set the
u
b
position.modes.
Advertisement
Table of Contents
