Related Manuals for abi IMAGE IQBoardPS
Summary of Contents for abi IMAGE IQBoardPS
-
Page 1: Interactive Whiteboard
User Manual for IMAGE IQBoardPS Interactive Whiteboard Interactive Software Not Included Driver Software Only Copyright(C) 2009 A Brighter Image Pty Ltd Web: www.abimage.com.au or www.iqboard.com.cu Tel: +02 9938 6866 Fax: +02 9938 6899... -
Page 2: Table Of Contents
Contents Brief Introduction ......................... 3 1:Specifications ........................ 4 2: Warning prior to Installation ..................5 Installation Method ......................6-9 1: Installation of Hardware ................... 6-8 2: Installation and Uninstall of Software ................9 Uninstall software ...................... 9 3: Connect the data line ....................9 4: Orientation ........................ -
Page 3: Brief Introduction
Brief Introduction The IMAGE IQBoardPS Interactive EWB is the latest equipment for teaching, training and conference presentation. It incorporates the latest high-tech research results, such as top electronic technology, software technology, internet technology, etc. It will be the major instrument for modern information-based teaching, conference, distance education and training, gradually substituting for traditional teaching methods and conference mode. - Page 4 pecification and Configuration 1. Product specification Code “PS” stands for EPressure Sensitive technology code & the number 60, 80, 100, or 112 is the diagonal length in inches. 2. Standard package supplied: Pressure Sensitive IWB (Model PS): # White Board (1), # Stylus Pen (2), # Wall hanging bracket (1), # USB cable (1),...
-
Page 5: 2: Warning Prior To Installation
Warning prior to Installation Do not look directly at the projector light. Don’t leave cables that may causing tripping. If the cables must be put on the floor, straighten and tape them to the floor using “gaffer” tape. Environment Please do not put any electrical wiring within 50cm of the EWB. -
Page 6: 2: Installation And Uninstall Of Software
2: Installation and Uninstall of Software Install Interactive software Note: There are 2 software programs to load. Please double click on the software in the CD supplied, and follow the instructions: IQBoard ET&PS Drivers - Board drivers and calibration software IQ INteractive Software - Board Presentation software (if software purchased with board) Do not connect the data line before installing the software. -
Page 7: 1: Operation Hints
Operation Hints: Note: The Hot Key buttons on the board are designed to operate with the IQSoftware and will not work when used with third party software. For best results, the following recommendations should be followed: 1. Face the whiteboard when operating and writing on the projected image. To avoid harm to your sight, do not look straight at the projector when you turn back to face the students. - Page 8 Pen Operation: Click, Double click: Do not move pen or finger; press the surface lightly in close quarters (1-2mm). (Note: Since the whiteboard and the whiteboard pen are delicate electronic products, please do not hit the surface heavily, to avoid damaging the whiteboard and the pen point) Dragging: Press the surface with the stylus pen or finger, and drag it to the appointed position (the pen or finger should not leave the surface midway)
-
Page 9: Faqs
Then connect them again. If they placed. still don’t work, contact ABI. - 12 -... - Page 10 List any software changes made (1) Some times the mouse doesn’t work since the mouse started acting and some times it works normally. This 4. Mouse is strange and contact ABI. means there is probably a software not working driver conflict. properly.
-
Page 11: Whiteboard Maintenance
Whiteboard Maintenance Please exit the system before cleaning and it’s preferable to exit system and standby projector so that any marks are easily seen. (Note: Although the whiteboard can be used with dry erase pens, it is inevitable that with age or after cleaning with abrasive cleaners, a build up of dirt and ink will occur, detracting from the projected image. - Page 12 Three years warranty is provided on the board and its operation. The service “back to base”, so the client has to return the board to ABI and ABI will organize the return of the board to the user. It does not include: (1) Accessories (pens, batteries, cable).