Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Sparco Corsa Sparco F500i Isofix
Summary of Contents for Sparco Corsa Sparco F500i Isofix
- Page 1 1 Sparco F500i ISOFIX for Group INSTRUCTION MANUAL 9-18...
- Page 2 WARNING! PLEASE READ THOROUGHLY BEFORE COMMENCING INSTALLATION AS AN INCORRECT INSTALLATION COULD BE DANGEROUS. DO NOT USE THIS CHILD SEAT IN PASSENGER SEATS EQUIPPED WITH AIRBAGS. This child seat must only be installed in a forward facing position in passenger seats. Do not use on side facing or rear facing seats .
- Page 3 WARNING! Car interiors can become very hot when in direct sunlight, it is therefore recommended that the child seat is covered when not in use this prevents components ,particularly those attached to the child seat ,becoming hot and burning the child. Luggage and other heavy or sharp objects should be secured in the car, loose objects are liable to cause injury in the event of an accident.
- Page 4 Know Your Child Car Seat 1. Seat cover 2. Seat shell 3. Upper shaft and lock 4. Lower shaft and lock 5. Lock-o device 6. Belt guard door 7. Red hooks 8. Warning marking 9. Belt yoke 10. Seat base 11.
- Page 5 Installation Five positions of the car seat The car seat can be used in five positions: lift the handle under the front of the seat up and pull or push the shell forwards or backwards. Release the handle in the required position and push until you hear a distinct click.
- Page 6 Extend the floor support leg fully out ,adjust the height of the floor support leg to make sure the leg is reached the floor of your car. Installing the car seat using a 3-point safety belt with floor support leg. Group 1 (9-18kg) This child seat can also be installed with a 3-point safety belt, however always in combination with the...
- Page 7 Thread the car belt through the seat base and secure the car belt in the belt buckle. Make sure the lap portion of car belt fits under the red hooks, the diagonal portion of car belt runs from the belt buckle directly diagonal upwards.
- Page 8 Extend the floor support leg fully out, adjust the height of the floor support leg to make sure the leg is contacted to the floor of your car firmly. Fit your child with harness system. Group (9-18kg) Loosen the shoulder belts by pressing the release button and pulling the shoulder belts towards you.
- Page 9 The correct belt height of the shoulder belts is attained when the belt disappears into the shell slightly above the shoulder of the child. Make sure that the shoulder belts fit properly over the shoulders of the child. Adjusting the height of the shoulder belts The shoulder harnesses can be set to four heights and must be passed through the holes closest to the shoulders of your child.
- Page 10 Open the belt guard door. remove the shoulder belts from the metal retainer clip and the shoulder strap connector. Pull the shoulder belts through the shell and the cover , then place them at the desired height using the same slits in both the cover and the actual seat.
- Page 11 Close the belt guard door. Take the lower shaft in to the seat. Remove the harness system Adjusting the child car seat into the most-reclined position , then take the lower shaft out of the seat.
- Page 12 Tilt the seat shell forward. Open the belt guard door . Remove the harness belt from the belt yoke. Pull out the metal part which is used to fasten the shoulder pad strap to the back of the seat shell.
- Page 13 Pull the harness belts and the pads out of the belt slots. Then open the harness buckle . Pull out the metal part which is used to fasten belt to the bottom of the seat shell. Push the metal plate, with which the harness buckle is fixed to the seat shell on its side upwards through the belt...
- Page 14 Removing and refit the seat cover Removing the harness . Take the elastic loops of the cover o the hooks under the edge of the seat shell. Now you can remove the seat cover. Refitting the seat cover To refit the seat cover on the seat just hook up the elastic bands to its hook stand.
-
Page 15: Care Instructions
Care instructions Washing instruction The seat cover can be washed with Luke-warm water and a gentle soap. Do not use any abrasive detergents. The cover must be washed by hand at a maximum temperature of 30°C. Do not use dry cleaning (see also washing instructions). The buckle may be cleaned with warm water. - Page 16 NOTICE This is an ISOFIX CHILD RESTRAINT SYSTEM. It is approved to Regulation No.44,04 series of amendments for general use in vehicles fitted with ISOFIX anchorages systems. It will fit vehicles with position approved as ISOFIX positions (as detailed in the vehicle handbook), depending on the category of the child seat and of the fixture.
Need help?
Do you have a question about the Sparco F500i Isofix and is the answer not in the manual?
Questions and answers