Page 1
Chassis : KSBH(P)_CB1J Model : CS21A530FLKXSV 1. Precaution 2. Product Specification 3. Disassembly & Reassembly 4. Troubleshooting 5. Exploded View & Part List 6. Wiring Diagram 7. Schematic Diagram CS21A530FL Refer to the service manual in the GSPN (see the rear cover) for the more information.
These two grounding systems are separated in the circuit using an unbreakable/unchangeable insulation material. 8. When any parts, material or wiring appear overheated or damaged, replace them with new regular ones immediately. When any damage or overheating is detected, correct this immediately and make a regular check of possible errors. Samsung Electronics...
Page 5
Critical safety parts should be bracketed with ( , ). Use only regular parts for replacements (in particular, flame resistance and dielectric strength specifications). Irregular parts or materials may cause electric shock or fire. Samsung Electronics...
The ground lead of the tester should be removed last. 9. Beware of risks of any current leakage coming into contact with the high-capacity capacitor. 10. The sharp edges of the metal material may cause physical damage, so protect yourself by wearing gloves during the repair. Samsung Electronics...
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Samsung Electronics...
6. Keep the antenna far away from any high-voltage cables and install it firmly. Contact with the high-voltage cable or the antenna falling over may cause fire or electric shock. 7. Check the basics of the screen test. - Image position/size, Tilt adjustment, Actuator activation . Samsung Electronics...
Rear:1 Rear:1 Extermal In Rear: 2 Rear: 1 S-Video Y/Pb/Pr Ports HDMI Digital Audio Out Video Out Rear.1 Rear:1 Remote Controller TM930 TM930 For the power supply and power consumption, refer to the label attached to the product. Samsung Electronics...
Check that the Master Switch has been pressed. Ch eck that the transmitter is turned on. Check that transmitter device selection is set to TV. Check that the signal cable is properly connected. Check that channel setting has been set. Samsung Electronics...
AV item is grayed out, you cannot select an A/V channel. Check if the connector is properly connected. Check if the menu is grayed out. If a menu is grayed out, it cannot be Cannot select a menu. selected. Samsung Electronics...
Page 16
■ Set the auto volume control to ON. There is a lot of noise. Keep the antenna away from the power cord or connectors if possible. The selected language does not appear. Press the Multiplex button to select the TV. Samsung Electronics...
Page 17
This noise may occur when the plastic material inside the TV expands or The TV makes a noise as if something is dropping contracts according to the seasonal temperature or humidity. This is like the inside. noise from a furniture/cabinet/sink unit, and there is no need for concern. Samsung Electronics...
Page 18
Therefore, you can determine whether the software has been properly downloaded, if you know the correct checksum for that version of the software. You can check the checksum according in the following order. Factory Mode Checksum Enter Output Checksum (e.g. 0xab2b) ■ Checksum Examples T-SIXPEANL-1000.3 Checksum=E068 Samsung Electronics...
Page 19
Main Board. the cable from the Connect the cable Main Board th the CRT Ass’y properly innected? SOUND IC BRIDGE DIODE SMPS-TR VERTICAL IC MAIN TRANS MICOM SMD IC EW DRIVER DY-JACK TUNER OUTPUT TR Q401 INPUT JACK Samsung Electronics...
Is the power cord or the master switch out of order? Check the others part Check the “D801S” #1 Check the FUSE “FP801S” Check the IC801S #1 W6753F Change “FP801S” Change “D801S” Change “IC801S” Complete F801A BRIDGE DIODE SMPS-TR Samsung Electronics...
2. No Sound - when the power is normal No sound (1st power OK) Check the +14V line Check IC201 Pin#39.40 Check FD801S Check D809C Change IC601 Change FD801S Change D809C Complete D809C FD801S MICOM SMD IC SOUND IC Samsung Electronics...
Page 22
Check the others B+ line T444 B+ Pin #3 “D811” Check D407 CHECK CRT ASS`Y open and check Open and check Change the “D811” Check the “Q401” Change D407 Change the “Q401” Complete MAIN TRANS D407 OUTPUT TR Q401 Samsung Electronics...
If there is no signal measured even though the RF signal received by the external antenna is input to the Main Board Tuner. - Supplied Power: 5V, 8V, 33V - RF Trouble Check: Check CVBS output - AUDIO Trouble Check: Check SiF Signal output B+5V B+33V 4-10 Samsung Electronics...
Page 24
If the signal input change “and output are” to “is” not detected, check the following. - Supplied Power: UOC TOP IC(5V, 3.3V, 8V) - Input Problem Check: Check the connecting jacks. MONITOR-OUT-L AV2-IN-L AV1-IN-L MONITOR-OUT-R MONITOR-OUT-V AV1-IN-R AV1-IN-V AV2-IN-V AV2-IN-R AV1-IN-L AV2-IN-V AV2-IN-R Monitor-OUT-R MONITOR-OUT-V AV-IN-V AV-L-IN AV-R-IN MONITOR-OUT-L Samsung Electronics 4-11...
If there are some ‘spotted’ points on the screen when displaying a black and white picture, degauss the screen using the degauss coil. If the spotted points remain, re-adjust the purity and the convergence. This completes the basic performance examination. 4-14 Samsung Electronics...
Data Required Adjustment x: 265± 5 y: 265± 5 Y: 45± 3 White Balance White Balance (Standard Data) x: 265± 5 y: 265± 5 Y: 1.5± 0.3 Toshiba Pattern Screen Voltage Same As KSCB Chassis G2 Adjust Samsung Electronics 4-15...
Page 29
2. Hotel Option Initial Data Item Selection Others Indonesia model Hotel Mode On/Off Power On Channel 0 ~ 99 Power on volume 0 ~ 100 Max Volume 0 ~ 100 Pannel Button Lock On/Off Power On Source Off/TV/AV1/AV2/DVD 4-16 Samsung Electronics...
Page 31
R Cutoff Adjust G Cutoff B Cutoff Adjust R Drive Adjust G Drive B Drive Adjust Sub Bright Adjust Sub Contrast Adjust Bluescreen Contrast Adjust G2 Adjust Bright 9 TR AKB Option Cathode Drive Level W/B adjust Margin 4-18 Samsung Electronics...
Page 32
Item Data Initial value Remarks RF AGC Adjust 2.11±0.05V IF AGC Speed IF Demodulator Fast Filter IF PLL RF FOA/FOB VCR RF output AV FOA/FOB RF PAL Ident Sensitivit RF NTSC Ident Sensitivit AV PA/NT Ident Sensitivit Samsung Electronics 4-19...
Page 33
Wide Blanking Front Secam Blanking Wide Blanking Rear Secam Blanking Cut Off Contorl Range 8. YC Delay Item Data Initial value Remarks PAL Delay SECAM Delay NTSC Delay PAL AV Delay SECAM AV Delay NTSC AV Delay 4-20 Samsung Electronics...
Page 34
0: 123 degree Dynamic Skin 1: 117 degree Gamma & White Stretch 0 ~ 3 0: No black level shift DC Transfer Ratio 1: black level shift 0: Japanese matrix NTSC Matrix 1: USA matrix DCXO CAP Samsung Electronics 4-21...
Info Menu Mute Power On” using the remote control and enter Factory Mode. 3. Enter Deflection Mode. 4. Adjust the V-AMP, V-SHIFT, H-EW and H-SHIFT items so that the width becomes 92 and the height becomes 92. 4-22 Samsung Electronics...
Page 36
7. When the adjustments are complete, display the Lion pattern and check that the picture size has not been changed. If there is no change, finish the adjustments. Samsung Electronics 4-23...
Page 37
Adjusting the Screen Voltage 1. Select: Power OFF Info Menu Mute POWER ON 2. Initialize all settings to the values appropriate to the corresponding model make sure the video adjust 1 is the factory date,just as the following picture. 4-24 Samsung Electronics...
Page 38
Mute POWER ON 1. Select: 2. Initialize all settings to the values appropriate to the corresponding model. 3. Display the Toshiba pattern and adjust the White Balance using CA100 with the coordinates of the corresponding model. [CA100] Samsung Electronics 4-25...
Page 39
4. When the adjustment is finished, check the following checklist. - If there is a spot on the screen when turning the TV set off/on, adjust the Screen Voltage again. - If there is a ghost line on the screen, adjust the Screen Voltage again. 4-26 Samsung Electronics...