Geemarc Ampli100VM Installation And User Manual
  1. Manuals
  2. Brands
  3. Geemarc Manuals
  4. Telephone
  5. Ampli100VM
  6. Installation and user manual
Geemarc Ampli100VM Installation And User Manual

Geemarc Ampli100VM Installation And User Manual

Amplified telephone with outgoing voice modulation
Hide thumbs Also See for Ampli100VM:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Ampli100VM
Amplified Telephone With
Outgoing Voice Modulation

Advertisement

Table of Contents
loading

Related Manuals for Geemarc Ampli100VM

Summary of Contents for Geemarc Ampli100VM

  • Page 1 Ampli100VM Amplified Telephone With Outgoing Voice Modulation...

  • Page 2: General Description

    DESCRIPTION General Description Indirect Clip for Quick Dial Line memory wall locations, cord Hold Voice button mountin M1,M2 and socket* button meter Customer Service Key Ringer Volume settings Ringer tone setting Sending level amplified setting Numeric keypad Amplify R button Handset Memory Last number...
  • Page 3 DESCRIPTION Rear Amplify Dialing Flash Voice level Telephone default mode setting meter setting line socket setting setting Base Thread the line cord through this groove...

  • Page 4: Installation

    INSTALLATION 1 - Connecting Telephone 1 - Connect the handset cord. 2 - Connect the line cord to the socket located at rear of telephone then connect the PTT plug*. (*) Classified TNV-3 according to EN60950 standard. 2 - Ringer Volume Setting A switch located on the right side allows the ringer to be switched to HI, LOW or OFF.

  • Page 5: Wall Mounting

    INSTALLATION 4 - Wall Mounting To wall-mount your telephone, slide out the clip turn around and slide back into the wall mounting position (located in the base unit, just below the ear piece).This will ensure that the handset stays firmly in position. Make 2 holes in the wall 85mm apart, insert the wall plugs and the wall mounting screws.

  • Page 6: Using The Phone

    USING THE PHONE 1 - Answering Incoming Call - When an incoming call is received the phone will ring and flash. To answer the call lift the handset and speak. - On completion of the call, carefully replace the handset in the cradle to release the line.

  • Page 7: Making A Call

    USING THE PHONE 4 - Making A Call - Lift the handset. - Await the dial tone and dial required number. - On completion of the call, carefully replace the handset in the cradle. 5 - Sending Level Adjustment If your voice is quiet or called parties have difficulty hearing you, you can increase the sending level volume with the switch located on the right side.

  • Page 8: Dialling Stored Number

    USING THE PHONE - Press one of the direct memory buttons, M1, M2, CS. Or press M and any button 0 to 9 on the key pad under which you wish to store the telephone number in indirect memory. Replace the handset. Note : Numbers will be lost if you disconnect your phone.

  • Page 9: Flash Time Setting

    USING THE PHONE Hold Off: In hold mode, put the handset on cradle. Then pick up the handset again or if the parallel phone goes off hook, the Hold function will be disabled and all speech meter LEDs are turned off. 12 - Amplification Setting a.Set the AMPLIFY Switch located at rear side of unit to ON...

  • Page 10: Regulatory Compliance

    REGULATORY COMPLIANCE - This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
  • Page 11 REGULATORY COMPLIANCE Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 12 Opening the equipment or any attempt to perform repairs will void the warranty. For service or repairs, call 1-888-864-2446 (To setup the auto dial feature for Sonic Alert/ Geemarc customer service the Green CS key must be programmed with the following phone number 1-888-864-2446.
  • Page 13 GUARANTEE Sonic Alert warrants the phone against any defect in materials or workmanship for the period of one year from the date of purchase. Should you experience a problem, contact our customer service department Be sure to save your sales receipt as proof of purchase date should you need warranty service.
  • Page 14 GUARANTEE Simply send the Ampli100VM (postpaid) and a copy of your sales slip as proof of purchase to: Sonic Alert Warranty Center 1081 West Innovation Dr. Kearney, MO 64060 IMPORTANT : YOUR RECEIPT IS PART OF YOUR WARRANTY AND MUST BE RETAINED AND PRODUCED IN THE EVENT...

Table of Contents