Shenzhen AS201 User Manual

Gsm/gps alarm tracking kit

Advertisement

Quick Links

GSM/GPS ALARM
AS201
'
USER
S GUIDE
T
KIT
RACKING
Multi-application
|
Satellite Tracking
|
Wireless Sensor Connection

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AS201 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Shenzhen AS201

  • Page 1 GSM/GPS ALARM AS201 ’ USER S GUIDE RACKING Multi-application Satellite Tracking Wireless Sensor Connection...
  • Page 2: Table Of Contents

    3.17 Doppler Movement Detection..........................18 3.18 Wireless Sensor Detection............................ 18 3.19 Daily Travel Mileage SMS report to Driver ( A authorization Phone No.)............19 3.20 OTA firmware............................... 19 4. Problem Shooting..............................20 APPENDIX................................... 20 Copyright © 2015 Shenzhen ANB Technology Co., Ltd. All rights reserved.
  • Page 3: 1-Introduction

    1-Introduction: AS201 is a GSM/GPRS/GPS alarm tracking box for multi applications. This small unit is equipped with Quad Bands GSM/GPRS module, Hi-sensitivity GPS receiver and 3D Accelerometer. It’s also can be connected with optional wireless/wired accessories like PIR senor, Doppler...
  • Page 4: Typical Application

    GSM Antenna x 1PC GPS Antenna x 1PC 14Pin Power+I/O Wire harness x 1PC Panic Button x 1PC Engine Cut-off Relay x 1PC Microphone x 1PC 1.4.2 Optional Accessories Copyright © 2015 Shenzhen ANB Technology Co., Ltd. All rights reserved.
  • Page 5: 2-Knowlege Before Usage

    2-Knowlege Before Usage: 2.1- How it works? The AS201 mainframe works as a host box with multi input/outputs. The mainframe will process to get GPS location and various working status from inputs and wireless sensors, and then send those information to preset Phone Numbers or IP/Port Server via GSM network.
  • Page 6: Power Supply

    2.3 Power Supply 2.3.1 External Power and Internal Power AS201 works with two power supply mode: External Power and Internal Battery. It's working normally with external power supply range from 9-36V DC. When the external power is disconnected or with low voltage output, device will switch to work on internal battery automatically. And it also will send"...
  • Page 7: How To Configure Device (Configuration)

    For other wireless sensor, like Door/window contact, Smoke and gas detectors follow the same process to integrate them to system. 2.5 How to configure device (Configuration) AS201 box support configuration via SMS commands and also via PC program tool(Configurator) via connect AS201 with PC through USB cable. 2.5.1 Configure by SMS commands:...
  • Page 8 2.5.2 Configure by PC tool “ Configurator”: 1. Connect AS201 with PC via USB cable: 2.Install CP2102 USB-Serial Driver: Copyright © 2015 Shenzhen ANB Technology Co., Ltd. All rights reserved.
  • Page 9: I/O Introduction And Definition

    3. Run AS201 configurator.exe and get into following interface: 2.6 I/O Introduction and Definition 1. Main I/O ports Introduction: Copyright © 2015 Shenzhen ANB Technology Co., Ltd. All rights reserved.
  • Page 10: How To Insert Simcard To As201

    ShortCall(=0V, Effective) Black/White LED - Arm/Disarm Status LED Yellow/White LED + Orange Mic+ Microphone Balck/White Mic- Green/White Speaker + 3W Speaker Black/White Speaker - 2.7How to insert Simcard to AS201 Copyright © 2015 Shenzhen ANB Technology Co., Ltd. All rights reserved.
  • Page 11: Functions And Operation

    If in Armed status, the system was disarmed, and get no Door open or Ignition status operation within 60Seconds, system will automatic arm once. AS201 system allow user to enable/disarm Re-arm function according user’s usage habit. Re-Arm function Enable/Disarm Method:...
  • Page 12: Remote Stop Oil/Power Supply For Engine (Immobilizer)

    In Armed status, the system will keep Oil/Power supply in locked status. This is to protect burglar ignore alarm alerts and start vehicle to drive away. This function is default as Disabled. If the user want to activate this function, can use SMS command sent AS201 inserted SIMCARD number to switch on and off this feature.
  • Page 13: Shock Alert ,Crash Accident Alert And Crash Accident Data Logger

    Configure By SMS commands *1234*CS*m,x.x,y.y,z.z# Note: M value is the AS201 box sides serial No. It’s user identification purpose. User Can define any sides of the 6Sides as forward direction. Just keep it as this way in installation. Configure by Configurator program:...
  • Page 14: Voice Listen-In

    2) Display accident data log via chart with time frame and G value varies: 3.6 Voice Listen-in Call Center Number D and SMS center Service No. G call AS201, the system will put through to Voice Listen-in mode directly. AS201 also provide other two methods to start Voice listen-in Operation: 1.
  • Page 15: Battery Low Alert

    This is to solve problem if any operation fail and do quick problem shooting. 3.11 Locate in parking Lot AS201 provides two methods for user to quick locate where the vehicle is by Siren sound and light flashing. 1. By press Remote controller Siren button to make sound 2.
  • Page 16 3. Speed Over alert: After speed limit is break, the vehicle is not slow down to under limit within a configured time period, the AS201 will drive the siren sounding until the speed slow down to under limit. At the same time, AS201 will activate the “immobilizer”...
  • Page 17: Emergency Medical/Information Call To Center( Two Way Intercom)

    By Configurator program or SMS commands, user can configure one Call center Voice service Number D in AS201. After the short call button was pressed, the AS201 will start to call this D number and connect to talk with Call center support People.
  • Page 18: Mute Output Control For Original Car Radio

    Remote controller/SMS Commands/GPRS command of Arm/Disarm operation. 3.15 Mute Output control for Original car Radio: This Mute output is for audio intercom purpose. When incoming call rings, AS201 will generate a signal to for this output cable and block Radio voice.
  • Page 19: Daily Travel Mileage Sms Report To Driver ( A Authorization Phone No.)

    Default setting is all defense area in ON status. How to program sensor to AS201 Box? AS201 allow user to do sensor code programming via two methods: SMS Command and override via Panic button + ACC ON/Off switch. 1. Override via panic button and ACC status: 2.4.2 Transmitter and wireless sensor Program to AS201 box...
  • Page 20: Problem Shooting

    <<Please consult with factory for this upgrading IP address, Password and file name.>> 4. Problem Shooting APPENDIX <Available SMS Commands List> < AS201 Installation Diagram> Copyright © 2015 Shenzhen ANB Technology Co., Ltd. All rights reserved.

Table of Contents