Hy-Gain 600 Installation And Operation Instructions Manual

~
_ •...• U N EAR RF DECK
The Hy-Gain Model 600 Bi-Linear
compact ampI ifier of advanced design.
circuit, two tubes, two transistors.
tuned plate circuit for amplification
nals.
A special feature of the AmpI ifier is its dua,!-purpose versati 1-
ity. It requires an external power supply,
base station use or DC supply for mobile station use.
gether with a quick-release
to be easily transported between base and mobile stations.
The Ampl ifier has a .bui It-in
lay. which operates without special external connections,
it perfect for operation with low power transceivers
ternal amplifier control circuits.
'The amplifier also amplifies
~ted circuit amplifier.
is accessible through a hole in the top cqver, allows for
1
t""rtuning of the amplifier.
used to offer impedance matching for maximum output into a 50
ohm antenna system.
The Ampl ifier has been designed and constructed
radiation that may cause television
has been given full consideration
of the chassis. There are, however, some types of TVI that can-
not be prevented within the amplifier.
in weak signal areas. In such cases, a good commercial
pass fi Iter is recommended.
Operation of this equipmer
comply is punishable by penalties
RE>gulations of the FCC. A copy of these Ruies, for use under
the appropriate section', is available
Printing Office and should be in the possession
Carefully remove the Model 600 Bi-Linear RF Deck from the car-
ton. Examine it closely for signs of shipping damage. If inspection
.r---...,
damage the delivering carrier must be contacted immediately
_<I
claim filed.
ORDER NO.
GOO
GENERAL
Amplifier is a precision
It uti Iizes an integrated
two diodes and a tuned grid.
for AM, FM, CW and SSB sig-
eltber AC supply for
This, to-
mobile mount, allows the Ampl ifier
automatic antenna change over re-
having no ex-
the received signal, utilizing
The variable plate tuning capacitor,
An internal load capacitor has been
to suppress
interference. TVI problem
in the design and the layout
This"is particularly
.
requires a FCC license. Failure to
seT forth in the Rules and
from the U.S. Government
of the operator.
INSTALLATION
OPERATION
HV-GAIN
. Rural
SECTION I
DESCRIPTION
built,
Height (including
Width .......................................•....................
Depth.................................
Net Weight
Shipping Weight
Construction
Frequency Range
making
Types of Emission
Power Output
Ampl ification of Received Signal.
an in-
Drive ReqUired to Trigger Antenna Relay .....•.......•..•........
Max Drive (unmoduIated carri er and FM)..•..•.............•.......
(amplitude modulated carrier) ...............•.......
(amplitude modulated peak)
Harmonic Suppression
Input Impedance (unbalanced)."
Output Impedance (unbalanced)
Antenna Switching
Tube and Semiconductor Complement
true
low
Power Requirements
(obtained from either Model 601 Base AC Power Supply or Model
602 Mobile DC Power Supply)
ponsibility in obtaining reimbursement rests with you. Prompt action
will speed adjustment. Our warranty does not cover malfunction
damage which is a result of improper handling by a carrier.
&
INSTRUCTIONS
ELECTRONICS CORPORATION
3 • Lincoln. Nebraska 68505
Routl:
feet)
..
,..Lightweight
with rugged steel
AM, FM, CW, SSB, DSB
150 AM with full
300 Watts CW (with 3.5 watts driVe')
Exceeds FCC requirements
Less than 2 : 1 VSWR
Automatic provided by RF sensing network
.
+300v
-lOOv
12VAC or DC at 2.S amps
3 nches
7 1/8 nches
11 3/4 nches
4 1/4 pounds
6 pounds
al uminum chassis
case
26-35 MHz
upward modulation
20 db
1 Watt
15 Watts
3.5 Watts
14 Watts PEP
50 ohm nominal
50 ohm fixed
2 Tubes
2 Transistors
1 Integrated Circuit
+800v 700 mA
@
SOmA
@
@ 10mA
or