D-Link DWL-3140AP Install Manual

Wireless 108g web smart thin ap with poe
Hide thumbs Also See for DWL-3140AP:

Advertisement

Advertisement

Table of Contents
loading

Summary of Contents for D-Link DWL-3140AP

  • Page 2: System Requirements

    • 5V 1.2A Power Adapter • Mounting Bracket • Mounting Kit This access point can only be used with a D-Link DES-1228P wireless switch. Please refer to the xStack user manual for configuration of the access point. D-Link DWL-3140AP Hardware Installation Guide...
  • Page 3: Installation Considerations

    Installation Considerations D-Link wireless devices allow you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
  • Page 4: Before You Begin

    2. Do not touch or move the DWL-3140AP access point when the antennas are transmitting or receiving. 3. Do not hold any radio device so that the antenna is very close to or touching the face, eyes, or other exposed body part while the device’s radio antenna is transmitting.
  • Page 5: Front Panel

    Front Panel Rear Panel Power Receptor Receptor for the supplied power adapter. D-Link DWL-3140AP Hardware Installation Guide...
  • Page 6 Ethernet its original factory default port. This LED blinks during settings. data transmission. WLAN LED A solid green light indicates a wireless connection is ready. This LED blinks during data transmission. D-Link DWL-3140AP Hardware Installation Guide...
  • Page 7: Mounting Options

    Mounting Options You can mount a DWL-3140AP access point on any of the following types of surfaces: • Solid surface wall or ceiling • Tabletop Cable Requirement The Ethernet ports on the DWL-3140AP access point cannot accept a CAT 5 cable that has an uneven sheath. The RJ-45 connector on the cable will not seat properly in the receptacle on the access point.
  • Page 8: Solid Wall Or Ceiling Installation

    Solid Wall or Ceiling Installation 1. Remove the mounting bracket from the DWL-3140AP. 2. Attach the bracket to the wall or ceiling. 3. Mark the points where you will use screws. Take out the bracket. 4. Drill the marked points and insert the plastic wall mount.
  • Page 9 8. Plug the CAT 5 cable into the access point. 9. Attach the access point to the mounting bracket. 10. Gently pull the power cable and the ethernet cable as you slide up to lock the access point onto the bracket. D-Link DWL-3140AP Hardware Installation Guide...
  • Page 10: Warranty

    D-Link at an Authorized D-Link Service Office. The replacement hardware need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware.
  • Page 11 Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link.
  • Page 12 Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link.
  • Page 13 D-Link Corporation/ D-Link Systems, Inc., as stipulated by the United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.
  • Page 14 Notes D-Link DWL-3140AP Hardware Installation Guide...
  • Page 15 Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. D-Link DWL-3140AP Hardware Installation Guide...
  • Page 16: Technical Support

    Copyright ©00 D-Link Corporation/D-Link Systems, Inc. All rights reserved. D-Link and the D-Link logo are registered trademarks of D-Link Corporation or its subsidiaries in the United States and other countries. Other trademarks are the property of their respective owners. Maximum wireless signal rate derived from IEEE Standard 0.11g specifications. Actual data throughput will vary.

Table of Contents