Network; Philips Wirelessconnect; Net Tv - Philips 65PFL4909 User Manual

To obtain a more detailed electronic copy of this User Manual, go to www.philips.com/support

Network

Set up Network connection settings in order to use Net TV
or Network Upgrade function.
1
Display Setup using Home Menu and use H I to select
Installation, then press OK.
2
Use H I to select Network, then press OK.
Network Settings Assistant
Before you proceed to Connection test or other settings in
Network section, run the Network settings assistant to
connect the TV to your Network.
Wireless setting
Select to use a wireless LAN to connect to the internet by
wireless connection.
3
Use H I to select Network settings assistant then
press OK.
4
Press OK to select Start now.
5
Use H I to select Wireless, then press OK.
6
Use H I to select the desired setting, then press OK,
and follow the On-screen Instructions.
Setting items
Select this setting if your router has a Wi-Fi
Protected Setup (WPS) button. Start
scanning for Wireless Networks on the TV
Easy Connect
after pressing the WPS button on your
router. If connection test fails, refer to the
router's manual for more details.
Search for Wireless Networks automatically
Scan
and select the Wireless Network name
(SSID) from the list.
Set up the connection to the Wireless LAN
Access Point (AP) (e.g. wireless router)
Manual entry
manually by entering the Wireless Network
name (SSID).
Wired setting
Select to use an Ethernet cable to connect to the internet by
wired connection. Please purchase shielded Ethernet cables
at your local store and use it when you connect to Network
equipment.
3
Use H I to select Network settings assistant then
press OK.
4
Press OK to select Start now.
5
Use H I to select Wired, then press OK.
Connection test will start automatically. (Refer to Connection
●
test L p. 9.)
Description
Connection Test
Perform the following steps to test your internet connection
after you have connected an Ethernet cable or entered
Network settings such as IP address, DNS settings, etc.
manually.
3
Use H I to select Connection test, then press OK.
4
Press OK to select Start now.
Connection test will start automatically and the test result for
●
Home Network and Internet will appear right after the
connection test finishes.
"Testing..." is displayed while the connection test is in
●
progress.
Home
Internet
Network
Pass Pass
Fail
-
Pass Fail
If the connection test for Internet passes, speed test will start
●
automatically.
5
Press OK to go to the list of Network status confirmation
screen.
6
Press OK to exit.
Note(s)
O
If the connection test for both Home Network and Internet pass,
●
you are ready to use Net TV or Network Upgrade function using
the internet without making any additional settings.
If the connection test fails, check if the Ethernet cable is
●
connected to this TV properly or if you have entered all the
required details for the wireless LAN connection properly.

Philips Wirelessconnect

You can enjoy your TV as a PC monitor wirelessly using your
Home Network. Make sure you download the Philips
Wirelessconnect Software and install it on your PC before
you perform the steps below.
Install Philips Wirelessconnect
1
Display Setup using Home Menu and use H I to select
Software, then press OK.
2
Use H I to select Wirelessconnect code, then press
OK.
Write down the 12-digit code displayed on the screen. You
●
will need this to download Philips Wirelessconnect Software.
3
Start your internet browser on your PC and open the
Philips Wirelessconnect download page at
www.wifimediaconnect.philips.com/
On the website, you can check the necessary PC system
requirements.
4
Enter the 12-digit code you wrote at step 2.
5
Click the 'Download now' button to download the free
Philips Wirelessconnect Software.
6
Once downloaded, run the Philips Wirelessconnect
Software installer. Follow the On-screen Instructions to
complete Software installation.
9
Description
Connection test is successfully
completed.
Connection test for Home Network
failed. Check the connection settings.
Connection test for Internet failed.
Check the connection settings.
Continued on next page.