Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Alware Senrigan GP-55
Summary of Contents for Alware Senrigan GP-55
- Page 1 Senrigan GP-55 3-Axis Brushless Gimbal V2 With Bluetooth (For 600 -1000 Size Multicopter) Instruction Manual v1.0 25 Aug 2014...
-
Page 2: Table Of Contents
Table of Contents 1. Introduction.................................3 2. Check List................................5 3. Equipment Required For Assembly........................7 4. Assembly Step :..............................8 5. Tuning Tips................................16 End of Manual...............................18... -
Page 3: Introduction
The lower the weight, the longer the flying time you can achieve. Differ than others, the motors and Gimbal Controller of Senrigan GP-55 Brushless Gimbal have been well test a nd tuned of the PID parameter for NEX N5/ N7 Cameras in the factory before selling. So no worries about the s etting or PID tuning of the Brushless Gimbal. - Page 4 -Brushless Gimbal Motor Weight: 94g /Pcs -Brushless Gimbal with Controller: 652g (Without Camera) Included: 1x Senrigan GP-55 3-Axis Brushless Gimbal V2 (Non-assembled) 1x 32 bits SimpleBGC Camera Stabilizer System with Alu Case protection 1x Frame IMU Unit 1x Camera IMU Unit...
-
Page 5: Check List
2. Check List All the package should be packed and contain all the items as shown below. Please contact the vendor you purchased from if anything is missing at once. Damper plate up *1pcs Top plate *1pcs Damper plate down *1pcs (with big circle Round cap screws M3x4mm *4pcs in the middle.) Motor *3pcs... - Page 6 Black Pieces *4pcs Black gimbal piece *6pcs Camera nut *1pcs Alu rods *4pcs Scew pack *1pcs Boom mount yellow piece set *4pcs 32 Bits Gimbal Controller with case *1pcs Hex screws *8pcs Bluetooth Module *1pcs M3 self-nuts *8pcs Camera IMU with cable *1pcs Frame IMU with cable *1pcs Male to Male RC Cable *1pcs Power Cable *1pcs...
-
Page 7: Equipment Required For Assembly
3. Equipment Required For Assembly Sony Nex 5 / or Sony Nex 7 DJI S800 EVO kit / S1000 Alware Cyclone X8 Octocopter 2S 800Mah (or above) battery Connector to match your Battery... -
Page 8: Assembly Step
4. Assembly Step : **Always apply little amount of Threadlock when installing metal parts. Use M3x5mm screw only, screw longer M2.5x6mm Hex Cap Screw then 5mm will damaged the motor! M3x5mm Hex Cap Screw M2.5x6mm Hex Cap Screw... - Page 9 M2.5x6mm Phillip Flat Screw Use M3x5mm screw only, screw longer Use M3x5mm screw only, screw longer then 5mm will damaged the motor! then 5mm will damaged the motor!
- Page 10 M2.5x6mm Hex Cap Screw M2.5x6mm Phillip Flat Screw Use M3x5mm screw only, screw longer Install the Dampers then 5mm will damaged the motor!
- Page 11 Use M3x5mm screw only, screw longer then 5mm will damaged the motor! M3x6mm Hex Cap Screw Assembly...
- Page 12 Recognize the position of the Three Use two layers of Double Side Tap to Motors (Pan, Roll and Tilt motor). Stick the Camera IMU here. (Follow the orientation as shown) Install the Frame IMU using Double Connection Diagram of the two IMUs. Side Tape.
- Page 13 Install the Gimbal Controller using Connect the Bluetooth Module to the Round Cap Screw M3x4mm *2pcs Controller. (Tips: RX--> TX , TX--> Stick the Bluetooth Moudle as shown. Wiring all Motor and IMU wires through Connect the end side of the IMU wire to the center hole of the motors and along I2C port on the Controller.
- Page 14 Connect Motors to the Controller. Secure the Top Mounting Frame using 4pcs M3x6mm Hex Cap Screws. The Pan(+-360 degree) and Tilt(+45-90 degree) axis of GP-55 can be controlled by using any two Free channels of your receiver. Also by assigning a 2-way/ 3- way switch channel to “FC ROLL”...
- Page 15 Finish assembly. Mount GP-55 to the Multicopters.
-
Page 16: Tuning Tips
5. Tuning Tips Specification for the 32 Bits Alexmos Controller with GP-55V2 Gimbal 32 bits SimpleBGC Camera Stabilizer System with Alu Case protection Twins IMUs with Alu Case protection Firmware: The newest 2.42b6 (updateable freely in the future) Power supply voltage: 8–25 V (2s-6s LiPo), Default setting for 7.4v Lipo Maximum motor current: 1,5 A/ each motor Voltage Output: 5V 1A (suitable to power the receiver directly) Pre-programmed for Sony NEX N7/ similar size Mini DSLR Cameras. -
Page 18: End Of Manual
End of Manual...
Need help?
Do you have a question about the Senrigan GP-55 and is the answer not in the manual?
Questions and answers