Harman Kardon AVR65 Service Manual page 8

1
AM Antenna : Connect the AM loop Center : Connect these terminals to the
antenna supplied with the receiver to these center speaker.
terminals. If an external AM antenna is used,
make connections to the AM and GND Surround :
terminals in accordance with the instructions surround speaker.
supplied with antenna.
Unswitched AC Outlet :
2
FM Antenna : Connect an indoor or be used to power any AC device. The power
external FM antenna to this terminal. will remain on at this outlet regardless of
whether the AVR-65 is on or not.
3
Video 1 Inputs : Connect these jacks to
the audio and video PLAY/OUT jacks of a VCR. NOTE : The power consumption of the device
plugged into each of these outlets should not
4 Video Outputs 1: Connect these jacks to exceed 100 watts.
the audio and video RECORD INPUT jacks of a
VCR. Switched AC Outlet :
used to power any device that you wish to turn
5
6-Channel Direct Inputs : If an external on when the unit is turned on wiht the System
digital audio decoder is used for 5.1(Dolby AC- Power Control switch.
3)audio, connect the outputs of that decoder to
these terminals. Power Cable :
non-switched AC wall output.
6
CD Inputs : Connect these jacks to the
output of a compact disc player or CD changer. Video 2 Inputs :
audio and video outputs of a TV Tuner. Cable
7
DVD Inputs : Connect the analog audio TV converter box, satellite receiver of any other
outputs and composite video output of a DVD audio/video source.
or LD player to these jacks.
TV Monitor Video Output :
8
Pre-Outs : If external power amplifiers are jack to the standard(composite) video input of
used for any channels, connect them to these a TV monitor or video projector to view the on-
jacks. screen menus and the output of any standards
video source selected by the receiver's video
9
Subwoofer Pre-Out : Connect this jack to switcher.
the line level input a powered subwoofer. If an
external subwoofer amplifier is used, connect Coaxial Digital Input :
this jack to the subwoofer amplifier input. digital output from a DVD player, HDTV
receiver, LV player or CD player to this jack.
Front : Connect these terminals to the The signal may be either a Dolby Digital (AC-3)
front left/right speakers. signal, DTS signal or a standard PCM digital
source.
Connect these terminals to the
This outlet may
Optical Digital Input : Connect the optical
digital output from a DVD player, HDTV
receiver, LV player or CD player to this jack.
The signal may be either a Dolby Digital
(AC-3)signal, a DTS signal or a standard PCM
digital source .
Remote IR In : If the AVR-65's front panel
This outlet may be IR sensor is blocked due to cabinet door or
other obstructions, an external IR sensor may
be used. Connect the output of the sensor to
2 this jack.
Connet the AC plug to Remote IR Out : This connection permits
the IR sensor in the receiver to serve other
remote controlled devices. Connect this jack to
Connet these jacks to the the "IR IN" jack on Harman Kardon or other
compatible equipment.
Multi : Connect the output of an IR sensor
in a remote room to this jack to operate the
Connet this AVR65's multiroom control system.
Multiroom Audio Outputs :
jacks to the inputs of an optional audio power
amplifier so that the input selected by the
multiroom control system will be heard in a
remote room.
Connect the coax
Tape Monitor In : Connect these jacks to
the PLAY/OUT jacks of an audio recorder.
Tape Monitor Out : Connect these jacks
to the RECORD / INPUT jacks of an audio
Mute : This indicator illuminates to remind
you that the AVR 65's output has been silenced
by pressing the Mute button 25 .
Press the Mute button again to return to the
previously selected output level.
Bypass : This indicator illuminates when
the surround processing has been disabled by
pressing Surround Off button . When this
24
indecator is it, the AVR-65 will play transitional
stereo sound using the front left and right
speakers only.
Analog : This indicator illuminates when an
analog input source is in use.
Dolby Digital Indicator : This indicator
illuminates when a Dolby Digital source is
being played.
OPT. : This indicator illuminates when a
digital source is in use via a connection to the
Optical Digital input.
Dolby Pro-Logic Surround Mode
Indicators : These indicators illuminate when
one of the analog (matrix) or Digital(PCM)
Connect these
Dolby Surround modes is in use.
COAX.Source : This indicator illuminates
when a digital source is in use via a connection
to the Coaxial Digital input.
AC-3 Indicator : This indicator illuminates
when a AVR-65 is decoding a Dolby Digital
input source.
- 8 -
PCM Indicator : This indicator illuminates Auto : This indicator illuminates when the
to show that a standard PCM(SP/DIF) digital "Auto" mode is in use for FM tuning.
audio signal is being decoded by the digital-to-
analog converter. Stereo Indicator :
when an FM station is being tuned in stereo.
Surround Mode Indicators : These
indicators illuminate when one of the DSP Mono Indicator :
generated analog surround modes is in use when the tuner has been placed in the
with an analog input source. monaural mode by pressing the
button 18 . Set the tuner for mono listening to
Multiroom System Indicators : This cut noise and improve the quality of distant
indicator illuminates when the multiroom system stereo signals.
is in operation.
Tuned Indicator :
Night Indicator : This indicator lights when when a station is being received with sufficient
the AVR-65 is in the Night mode, which signal strength to allow for acceptable listening
prevents the AVR-65 from loud playback when quality.
digital sources are in use.
Main Information Display :
DTS Indicators : This indicator illuminates shows messages relating to the status, input
when a DTS encoded source is playing. source, surround mode, tuner, volume level or
other aspects of unit's operation.
Preset Number : This two-digit display
indicates the station preset number that is Sleep Indicator :
currently in use, or of that is being entered. illuminated when the Sleep function is in use.
The number that appears above the indicator is
Preset Indicator : This indicator illuminates the number of minutes remaining before the
when one of the stations entered into the AVR-65 will return to the Standby mode.
preset memory is tuned. The number that
appears below the indicator is the preset
station's memory.
Memory : This indicator flashes when
entering presets and other information into the
tuner's memory.
This indicator illuminates
This indicator illuminates
Tune Mode
This indicator illuminates
This display
This indicator is