Table Of Contents - Sony HT-BE1 Service Manual

HT-BE1/SA-WBE1/SS-BE1
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, "metallized" knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The "limit" indication is 0.75
V, so analog meters must have an accurate low-voltage scale. The
Simpson 250 and Sanwa SH-63Trd are examples of a passive
VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
To Exposed Metal
Parts on Set
0.15µF
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
2
AC
1.5k Ω
voltmeter
(0.75V)
Earth Ground

TABLE OF CONTENTS

1. SERVICING NOTE
1-1. Extension Cable and Service Position ................................ 3
2. GENERAL
Index to Parts and Controls ................................................. 4
3. DISASSEMBLY
3-1. Top Chassis Assy ................................................................. 5
3-2. Display Board, Key Board .................................................. 6
3-3. Rear Panel Assy ................................................................... 6
3-4. Main Board ......................................................................... 7
4. DIAGRAMS
4-1. IC Pin Descriptions ............................................................. 8
4-2. Block Diagram -Main Section- ........................................ 12
4-3. Block Diagram -Power Section- ...................................... 13
4-4. Printed Wiring Board -Jack Section- ............................... 14
4-5. Schematic Diagram -Jack/Main (5/1) Section- ................ 15
4-6. Printed Wiring Board -Main Section- .............................. 16
4-7. Schematic Diagram -Main (2/5) Section- ........................ 18
4-8. Schematic Diagram -Main (3/5) Section- ........................ 19
4-9. Schematic Diagram -Main (4/5) Section- ........................ 20
4-10. Schematic Diagram -Main (5/5) Section- ........................ 21
4-11. Schematic Diagram -Display/Key Section- ..................... 22
4-12. Printed Wiring Board -Display Section- .......................... 23
4-13. Printed Wiring Board -Key Section- ................................ 24
4-14. IC Block Diagrams ............................................................ 25
5. EXPLODED VIEWS
5-1. Main Section (SA-WBE1) ................................................ 28
5-2. Main Board Section (SA-WBE1) ..................................... 29
6. ELECTRICAL PARTS LIST
......................................... 30