Troubleshooting - Technics ST-C700 Owner's Manual

Using the system control
function
You can automatically link this unit with the SU-C700 and
operate them easily with the remote control.
Preparation
1 Connect this unit and the SU-C700 with a system
connection cable and a coaxial digital cable. (
2 Set the power switch lever of this unit and the SU-C700
to the [Í/I] position.
∫ Switching this unit and the SU-C700 to
on/standby simultaneously
≥ If you point the remote control at this unit and press
[NWP Í] when this unit and the SU-C700 are in standby
mode, this unit and the SU-C700 will be turned on
simultaneously.
≥ When both this unit and the SU-C700 are turned on and
the input source of the SU-C700 is set to "COAX1", you
can set them to automatically enter standby mode using
the sleep-timer. ( 21)
∫ Switching the SU-C700's input source
automatically
When you perform an operation such as playback on this
unit, the input source of the SU-C700 will be automatically
switched to "COAX1".
∫ Adjusting Bass/Middle/Treble
You can adjust the tone of the SU-C700 with this unit. Each
tonal range (Bass/Middle/Treble) can be adjusted.
1 Press [NWP].
2 Press [HOME].
3 Press [3, 4] repeatedly to select "SETUP" and then
press [OK].
4 Press [3, 4] repeatedly to select "Tone Control" and
then press [OK].
5 Press [3, 4] to select "On (adjustment)" and then press
[OK].
6 Press [3, 4] to select "BASS" (Bass), "MID" (Middle) or
"TREBLE" (Treble).
7 Press [2, 1] to adjust the level and then press [OK].
≥ Each level can be adjusted between "s10" and "r10".
≥ For information on the operations of the SU-C700, please also
refer to its operating instructions.

Troubleshooting

Before requesting service, make the following checks. If you
are uncertain about some of the check points, or if the
solutions indicated in the following guide does not resolve
the issue, then consult your dealer for instructions.
Heat buildup of this unit.
≥ This unit becomes warm when used for a long time. This is
not a malfunction.
9)
Do you have the latest firmware installed?
≥ Panasonic is constantly improving the unit's firmware to
ensure that our customers are enjoying the latest
technology. (
To return all settings to the factory defaults
When the following situations occur, reset the memory:
≥ There is no response when buttons are pressed.
≥ You want to clear and reset the memory contents.
1 Press [NWP].
2 Press [HOME].
3 Press [3, 4] repeatedly to select "SETUP" and then
press [OK].
4 Press [3, 4] repeatedly to select "Initialization" and
then press [OK].
5 Press [3, 4] to select "Yes" and then press [OK].
6 Press [3, 4] to select "Yes" and then press [OK]
again.
General
A "humming" sound can be heard during
playback.
≥ An AC power supply cord or fluorescent light is near the
cables. Keep other appliances and cords away from the
cables of this unit.
No sound.
≥ Check the volume of the connected device (amplifier, etc.).
≥ Check to see if the cable connections to the input and
output terminals are incorrect. If this is the case, turn off
this unit and reconnect the cables correctly.
≥ Check to see if the correct input source is selected.
≥ Insert the plugs of the cables to be connected all the way
in.
≥ When "Digital Output" and "Analog Output" are set to "Off",
no sound will be output. Change the setting of the output
terminal to be used to "On". (
≥ Playback of multi-channel content is not supported.
22)
20)
23