Summary of Contents for Garner PD-4
- Page 1 Model PD-4 (Physical Hard Drive Destroyer) Operation Manual 10620 Industrial Ave. Suite 100 Roseville CA 95678 (916) 784-0200 (800) 624-1903 4075-270 Rev H...
-
Page 2: Table Of Contents
Table of Contents Introduction ................................1 Important Instructions .............................. 1 PD-4 Component Identification ..........................2 Front Panel Identification ..........................2 Front Panel Description ............................ 2 Inside Component Identification ........................3 Inside Component Description ......................... 3 Operating the PD-4 ..............................4 Initial Startup ................................ -
Page 3: Introduction
TO DO SO MAY RESULT IN FREIGHT DAMAGE AND VOID WARRANTY. In the event that you must transport model PD-4 to a different location or to the factory for repair service, you must package it for safe delivery. Failure to do so may result in freight damage and will void the factory warranty. -
Page 4: Pd-4 Component Identification
Initiates the destruction function. Note: When pressed initially with the wedge in 2) Destroy Button the home position and in Auto Mode, the PD-4 will first Auto-size requiring a second push of the “Destroy” button. Toggles between Auto-Mode and Manual Mode when held down for three seconds or when Green, Yellow and Blue lights flash in a chasing sequence. -
Page 5: Inside Component Identification
Inside Component Identification Inside Component Description Prevents access to the hard drives and Destruction Wedge during the destruction process. If opened during the destruction process the 1) Door / Door Handle destruction wedge will automatically stop. When the door is closed, the destruction wedge will retract.. -
Page 6: Operating The Pd-4
4) Press the “Destroy” button. The PD-4 will destroy the media in the destruction chamber in a pre-set cycle and return to the previously set position to be ready to destroy the next piece of media of the same size. -
Page 7: Sequence Of Manual Mode Operation
After the PD-4 destroys the Hard Drives, small fragments of the hard drive may be left on the Support Rails and will be left in the Debris Tray. Sweep or vacuuming the fragments from the Support Rails into Debris Tray located on the bottom of the Destruction Chamber in between the Support Rails of the PD-4. -
Page 8: Instruction For Use
Use caution when bringing the PD-4 from a cold environment into a warm environment. If moisture has accumulated due to a sudden change of temperature, wait (1) hour before operating the PD-4. Do not use the PD-4 on uneven or unstable surfaces. Only use the PD-4 on a secure horizontal surface. Cleaning: Please wipe dirt off with a soft and dry cloth. -
Page 9: Parts List
Shaft, gear 3500-066D Gear, spur 60 tooth 3500-068 Motor, 110/115 4000-007 Power Supply, 90-264VAC 4300-026 Fuse, 10A 250V slow blow 4075-270H Manual, operation PD-4 4500-023 Relay, SS SPST 5A 4700-045 Resistor, R5 50W 5100-001 Pushbutton switch 5100-034 Switch, power rocker SA1400-216B... -
Page 10: Specifications
Shipping Weight 125 lbs (56.8 Kg) Physical Dimensions PD-4: 15.75 in. (L) x 7.1in. (W) x 14.1 in. (H) Case: 21 in. (L) x 25 in. (W) x12 in. (H) Shipping Dimensions 34 in. (L) x 26 in. (W) x 18 in. (H) -
Page 11: Declaration Of Conformity
Declaration of Conformity Page 9... -
Page 12: Limited Warrany
Garner; (e) to damage caused by service performed by anyone who is not a representative of Garner or a Garner authorized service provider; (f) to a product or part that has been modified to alter functionality or capability without the written permission of Garner;...