Page 1
SASE SC8E Scarifier Manual SASE Company, Inc. Phone 800.522.2606 or Fax 877.762.0748 www.SASECompany.com...
Page 2
SASE is able to provide unsurpassed service and technical support for the contractor. At SASE we engineer and manufacture our own equipment, which allows us to be in control of the quality of the equipment we sell. SASE offers a complete line of concrete preparation and polishing equipment, our newest introduction being our new line of PDG planetary diamond grinders, which is setting a new standard for the concrete grinding and polishing industry.
Page 3
Scarifier SC8E User Manual SASE Company Inc. Equipment Safety Policy Statement SASE Company, Inc. is adamant that safety is one of the highest priorities for both our employees and customers. When considering set-up and operation of any piece of equipment supplied, manufactured, distributed, rented or serviced by SASE Company, Inc., the safety and protection of...
SASE Company, Inc. Scarifier SC8E User Manual ____________________________________________________________________________________________________ Safety Communication READ AND UNDERSTAND BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT Safety Instructions are preceded by a graphic alert symbol of DANGER, WARNING, or CAUTION Imminent hazard which, if not avoided, will result in death or serious injury.
SASE Company, Inc. Scarifier SC8E User Manual ____________________________________________________________________________________________________ (PPE) Personal Protection Equipment Proper safety attire must be worn when operating this machinery. The operator must wear approved safety equipment appropriate for the job such as hard hat and safety shoes when conditions require.
SASE Company, Inc. Scarifier SC8E User Manual ____________________________________________________________________________________________________ Before Starting the Machine Perform a visual inspection of the entire machine and all daily maintenance according to the Maintenance Schedule. Locate and be familiar with all engine/motor and operating controls. For Gasoline models, obtain the Engine Manufacturer’s Owner’s Manual. Read it and understand it before continuing.
SASE Company, Inc. Scarifier SC8E User Manual ____________________________________________________________________________________________________ Switch motor OFF before disconnecting power. Do not disconnect power by pulling cord. To disconnect, grasp the plug, not the cord. Unplug power cord at the machine when not in use and before servicing.
SASE Company, Inc. Scarifier SC8E User Manual ____________________________________________________________________________________________________ Dust Warning Some dust created by grinding and other construction activities contains chemicals known to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals are: Lead from lead-based paints ...
Remove spark plug lead on gasoline engine models or disconnect the supply voltage connector on electric models before performing any maintenance. Disconnect the power cord at the machine. Operating Procedures for SC8E (GAS) Start-Up Add oil and gasoline to the machine.
Page 11
Dust Control: Should dust control be of concern, please contact SASE to inquire about our powerful dust control vacuums. The SC8E can be used with an optional 2” vacuum connection. If you need further assistance, please call our toll free number .800.522.2606.
Page 46
SC08E 5 POINT SMALL TUNGSTEN CUTTERS Theoretical Assembly ST5 FR200 Cutter Set - 800.ST5.72/100 Components: 72 Cutters - 700962 104 Spacers - 625.06.09A Attention: There can be a difference in number of spacers, but there must be a clearance of 1/8” to 3/16”...
Page 47
SC08E 5 POINT SMALL MILLING CUTTERS Theoretical Assembly SRM FR 200 Cutter Set - 800.SRM.20/100 Components: 20 Cutters - 615.01.11 100 Spacers - 625.06.09A Attention: There can be a difference in number of cutters, but there must be a clearance of 1/8” to 3/16”...
Page 48
SC08E 18 POINT STAR CUTTERS 29 CUTTERS 36 CUTTERS 29 CUTTERS 36 CUTTERS 36 CUTTERS 29 CUTTERS 36 CUTTERS 29 CUTTERS Theoretical Assembly SS FR 200 Cutter Set - 800.SS.260/00 Components: 260 Cutters - 615.01.04 Attention: There can be a difference in number of spacers, but there must be a clearance of 1/ 8” to 3/16”...
Page 49
(1) year from original date of purchase. In the event that you should have a claim SASE shall repair, replace or remedy the defective parts resulting from the faulty design, materials or workmanship. Note: This warranty is only valid for equipment either sold by SASE or by an authorized wholesaler or distributor.
Page 50
SASE PRODUCT & WARRANTY REGISTRATION WARRANTY IS VOID IF NOT RETURNED AND REGISTERED WITH SASE WITHIN 30 DAYS OF PURCHASE COMPANY NAME AND TITLE STREET ADDRESS CITY STATE COUNTRY PHONE EMAIL DATE OF PURCHASE SERIAL NUMBER INVOICE NUMBER OF PURCHASE...
Need help?
Do you have a question about the SC8E and is the answer not in the manual?
Questions and answers