GEMEL Serpi Star ND 5 Operating Instructions page 3

To disarm:
-
Press the transmitter push-button (A) twice or turn the ignition key to the ON position (without starting the
vehicle) and then press push-button (A) once. After disarming the system with the transmltter, if one of the
doors is NOT OPENED within 2 minutes, the immoblliser will re-activate with the same signals as before.
11) ENGINE IMMOBILISER AND ALARM SYSTEM AUTOMATIC ARMING
@ #
A
Passive arming, if enabled by programming, will be activated in the followlng manner.
Turn the ianition kev to the OFF Dosition. oDen and close the driver's door. After 45 seconds the dashboard
LED will iliuminate, i h e direction indicators kill flash twice and 2 buzzer tones will be heard. At this point the
engine will be immobilised. After a further 45 seconds the alarm will be armed. This is signalled by the
dashboard LED starting to flash. Automatic Armina does not activate the door lockina. Disarm bv Dressina
,
.
push-button (A) on the transmitter.
If you wish to temporarily disable the automatic armlng function, refer to section VEHICLE MAINTENANCE
OR GARAGE STOP.
12)
SIREN MUTING
With the siren sounding it is possible to mute the noise by pressing push-button (6).
This action does not disarm the system or change the alarm state.
13)
SIREN FUNCTION EXCLUSION
Depending on the 'Rules in Force' at a particular parking area i.e. near Hospitals etc. it is possible to arm the
alarm but exclude the siren in case the system
IS
triggered. To activate this feature carry out the following
steps:
Before
turning the ignition OFF, press push-button (A) for approximately 2 seconds (the dashboard LED will
illuminate for a moment). Turn the ignition OFF within 10 seconds. Now, arming the alarm in the normal
way will exclude the slren for that armed period.
14)
ALARM PROTECTIONS AND CAUSES
A
Your car can be protected by:
- Permetric protection (push-buttons):
- Protection through external module:
- Starting attempt:
-
Volumetric protection; (Only for GR 48 versions)
- Interior lighting.
15)
CAR CHECK
At the time of arming the system, the alarm checks the position of the doorslbootlbonnet switches to ensure
they are in the correct position i . e it checks if the doors are open or closed. If one of the doorslbootlbonnet
has been left open the alarm will respond by giving a single buzzer tone after the normal arming signals (if
programmed) and a single blink of the dashboard LED.
16)
ANTIDISTRACTION
e
#
After the disarming through the remote control. if one of the doors IS NOT OPENED within 2 minutes, then
the alarm will automatically rearm. (Without locking the doors).
17)
ALARM LIMITATION
A
For every arming cycle the alarms are limited to a maximum of:
STANDARD VERSION
6 due t o each of the following causes:
3 due t o each for:
-
Doors (PP); - Ultrason~cs (US) (Only for GR 48)
- Voltage Drop (3W): '
-
Optional sensor (SO)
- Ignition Attempt (TA);
-
Bonnet and boot opening (PC)
-
Voltage drop with armed alarm (CA) (All except ND 5
-
ND 13
-
GR48).
N.6: IN UK VERSION, ALL ALARMS ARE LIMITED TO 9
Pi,..
12
18)
ALARM STORAGE
IQL
PC-PP
If after d~sarmlng the alarm the dashboard LED
continues
to flash thls will slgnal that
0 1
01
US
one or more acoustlc alarms have occurred dur~ng your absence To ~dentlfy the
alarm cause consult adjacent table and the associated letters In the prevlous 9 1 191
Q I
3w
sectlon The alarm system goes on storlng thls slgnal untll you e~ther turn the
lgnltlon ON or rearm the alarm Q
JQI
0 1 0
m
Q L I Q L ~ Q L Q ~ 4
CA
l 9 )
AUTOFEED
(ND6 & GS3A98 only)
lip'
iv
0'
lo[
IQ
j o L
SO
The alarm module is provided w ~ t h internal batteries. If the alarm wires are cut or the vehicle battery is
disconnected. while the system is armed, the siren will sound on its own power supply. When the battery is
re-connected, the sound will stop within 30 seconds after the connection.
Autofeed will follow for a cycle of 30 seconds.
When arming the alarm if the back-up battery is dead then rnstead of the two normal
buzzer sounds, two d~fferent sounds will follow.
NB In GR48 version the function i s active only If integrated with GS3A98
REMOTE CONTROL BATTERY REPLACEMENT INDICATION
Your remote control contalns an alkal~ne battery
Csol
The alarm system will indicate when the battery needs t o be replaced i n 2 ways.
-
Whrle drsarmrng the alarm system the buzzersounds w~llget softer
-
The remote control LED will lkght up only for an Instant (20 mllllseconds) after whlch ~t
will remaln OFF even ~f you go on presslng the remote button
BATTERY REPLACEMENT
1
&ino
It 1 s Important to carry out the battery replacement near the veh~cle
Remove the screw at the back of the transmltter and separate the 2 halves of the case
Remove the old battery and replace 11 wlth a new one Be sure to replace 11 the rlght way
round Reassemble the transmltter and replace the screw
' s l
When replayhg a LITHIUM battery use model CR2032 3v Ensure the battery 1 s placed
with the
+
slgn on top and that contact
IS
not made wlth adjacent electronic components
Following battery replacement the transmltter LED
will
be on constant
To ext~ngu~sh the LED press push button (6) If the alarm does not respond carry out the
re-synchron~sat~on procedure SEE NEXT SECTION
NOTE Take care In ensurlng that you dispose the old battery so as not to harm the
environment
3V BATTERY
RE-SYNCHRONIZA TION
~ ~ 2 0 3 2
If the transmltter push button
IS
pressed more than 256 tlmes out of the maxlmum range of
the recelver then ~ t w l l l be necessary to carry out the procedure of re synchronlsatlon
Press buttons (A) and (6) simultaneously and hold untll the transmltter LED goes out (Approximately 10
seconds)
-
Releas~ng the buttons w ~ l l cause the LED to ~llum~nate
- Press one of the push-buttons wlthln range of the alarm
- The alarm should now respond
20)
IMMOBILISER
The lmmobil~ser module enables to carry out a multiple engine immobiliser In additional to the current alarm
device system. By arming the alarm device the immobil~ser module sets Itself automatically and starts
working at any motor stalling attempt Disarming is set through a coded control of the alarm devlce.
On activated alarm the module is always active even if disconnected from the alarm.
Required function
in
the Kit: ND 14 BMC
N o t required function
in
the K i t b u t which can b e coupled: ND 14 - ND 14 BM - ND 14 C - GR 48
N o t required function in the K i t b u t which can n o t b e coupled: ND 5 - ND 6 - ND 13