1. Manuals
  2. Brands
  3. Pure Reliability Manuals
  4. Lighting Equipment
  5. PANDA II PR-2100B
  6. Product manual

Pure Reliability PANDA II PR-2100B Product Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

PANDA II
PR- 2100B
This product manual contains important information about the safe installation and
use of this projector. Please read and follow these instructions carefully and keep this
manual in a safe place for future reference.
PR LIGHTING LTD.
Yingbin Road, Dashi Panyu, Guangzhou, 511430 China
h t t p : / / w w w . p r - l i g h t i n g . c o m

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PANDA II PR-2100B and is the answer not in the manual?

Questions and answers

Related Manuals for Pure Reliability PANDA II PR-2100B

Summary of Contents for Pure Reliability PANDA II PR-2100B

  • Page 1 PANDA II PR- 2100B This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. PR LIGHTING LTD. Yingbin Road, Dashi Panyu, Guangzhou, 511430 China h t t p : / / w w w .

  • Page 2: Table Of Contents

    Remote Controller (Optional) INTRODUCTION Thank you for purchasing our product PANDA II PR-2100B. This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference.

  • Page 3: Safe Usage Of The Projector

    SAFE USAGE OF THE PROJECTOR The following points are important for safety as well as for the smooth installation and performance of the unit When unpacking and before disposing of the carton check there is no transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.

  • Page 4: Installing The Projector

    INSTALLING THE PROJECTOR There are two ways to install the projector either hanging the projector from the ceiling or sitting on the floor. Mount the inner and outer brackets provided on the body of the projector. There are 2 M8 knobs provided to tighten the body of the projector and the two brackets.

  • Page 5: Power Supply - Mains

    POWER SUPPLY - MAINS Use the plug provided to connect the mains power to the projector. Paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector is supplied separately so that they may be individually switched on and off.

  • Page 6: Master/Slave Synchro Mode

    5-PIN AND 3-PIN CONVERSION PANDA ‫ װ‬uses 3-pin XLR plug / socket. If your controller uses 5-pin XLR plug / socket, you should convert 5-pin plug / socket into 3-pin socket / plug as shown below. DMX TERMINATOR In the Controller mode or Master/Slave mode, the DMX output has to be connected with a DMX terminator at the last fixture in the chain.

  • Page 7: Controller Mode - Dmx 512 Operation

    CONTROLLER MODE – DMX 512 OPERATION CONNECTING CONTROLLER WITH PROJECTORS Connect the controller’s output to the first projector’s input, and connect the first projector’s output to the second projector’s input. The rest may be deduced by analogy. Eventually connect the last fixture’s output to a DMX terminator as shown in the figure below.
  • Page 8 No.1 to No.256. Each luminaire has 10 DIP switches with the numbers of #1, #2, #3, #4, #5, #6, #7, #8, #9 and #10. (For the PANDA II PR-2100B, set all #10 switches on the “OFF”) In the table, “0” means the switch is on the “OFF”, and “1” on the “ON”.

  • Page 9: Remote Controler Mode

    REMOTE CONTROLLER MODE The optional remote controller is used in Master/Slave mode. When you insert the remote controller’s plug into the master’s AUDIO socket (as shown in the following figure), you may control all projectors for shutter / open (STAND BY button), slow / fast strobe movment (STROBE button) and slow / fast action to respond to music (SLOW/FAST button).

  • Page 10: Troubleshooting

    TROUBLESHOOTING PROBLEM RESOURCE The projector does not start Check the fuse on the socket is blown or not. Check if the lamp is good or not. The projector switches on but does not Check setting the DIP switch is correct. answer to commands Check the XLR cable is good.

  • Page 11: Electrical Diagram

    ELECTRICAL DIAGRAM panda II manual.doc 11/12...
  • Page 12 COMPONENT ORDER CODES NAME PART NO. REMARK TRANSFORMER 040050003 230V50Hz/120V60Hz THERMOSTAT 190010054 95℃/10A 030060008 DC12V LAMP 100040051 EFR 15V/150W RELAY 192010018 BRIDGE 150050012 8A/1000V (COLOR/GOBO) MOTOR1 030040051 42BYGH036-10A (MIRROR PAN) MOTOR2 030040050 42BYGH036-09A (MIRROR TILT) MOTOR3 OPTICAL-COUPLE 171000008 MOC3022 230040119 MICROPROCESSOR U1~U3 170110002...

Table of Contents