Page 1
XL FRAMING 1200 PR-2970/PR-2970M This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. PR LIGHTING LTD.
INDEX SAFE USAGE OF THE PROJECTOR INSTALLING THE PROJECTOR FITTING THE LAMP POWER SUPPLY – MAINS CONTROL CONNECTIONS DMX TERMINATOR SETUP OPTIONS-PROJECTOR CONFIGURATION TO SET THE DMX START ADDRESS OPERATION MENU ERROR MESSAGES REPLACING GOBOS DMX PROTOCOL LED INDICATION MAINTENANCE LUBRICATION KEEPING THE PROJECTOR CLEAN TROUBLESHOOTING...
SAFE USAGE OF THE PROJECTOR When unpacking and before disposing of the carton check there is no transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus. The projector is for indoor use only, IP20.
INSTALL THE PROJECTOR WARNING SAFETY CORD (2PCS) To pass 2 SAFETY CORDS through 4 HOLES for safety! CLAMPS (2PCS) HANDLES (2PCS) Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each clamp.
Page 5
POWER SUPPLY-MAINS Connect the power cord as follows: L (live) =brown E (earth) =yellow/green N (neutral) =blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off.
DMX TERMINATOR In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals. The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain.
Page 7
Press button ENTER to confirm; In the same time. The GREEN LED will flash one time. It means the setting has been enabled. Press button FUNC, it will return to the upper menu one by one. 7/26...
OPERATION MENU 1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL PR LIGHTING XL SERIES DMX Address=001 XL FRAMING 1200 DMX Address DMX Address (001-512) Reset Reset Are You Sure? DMX Mode Standard 16 DMX Mode DMX Mode Extended 16 DMX Mode Short 8 Lamp Control By Control Channel...
Page 9
CMY Invert CMY Invert CMY Invert CTO Invert CTO Invert CTO Invert Defaults Defaults Defaults Restore Defaults Display On Always Display Mode Display Off After Delay Disp Dim Level Disp Dim Level Disp Dim Level Disp Dim Level Disp Dim Level Disp Dim Level Display Dimming Display Options...
Page 10
Pan and Tilt = Pan and Tilt X.X.X Power Board = Power Board X.X.X DMX Channel View DMX values Factory Setup Factory Setup Factory Setup Test Modes Self Test Self Test self test Status = XXX Lamp Status Lamp Manual Control = Control Turn Lamp On...
ERROR MESSAGES In the course of launch, XL FRAMING 1200 examines automatically whether there are errors and if there are, it will display information as follows: Display Message Sensor Err S1-M1 Colour wheel (1# drive board motor 1) error Sensor Err S1-M2 CTO (1# drive board motor 2) error Sensor Err S1-M3 CYM-cyan (1# drive board motor 3) error...
DMX PROTOCOL Short Standard Extended FUNCTION DESCRIPTION mode mode mode 000-010 Black 011-025 Open Strobe 026-225 Strobe speed from slow to fast 226-255 Open 000-007 Black Dimmer 008-255 Dimming from dark to light (0-100%) Dimmer Fine 000-255 Dimmer in 16 Bit precision 000-016 White 017-035...
LED INDICATION DMX signal OK Green No DMX signal Flash DMX signal error Yellow Setting the panel Blue Power Running self test mode Red/Green Green Reserved MAINTENANCE If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in any way it must be replaced.
TROUBLESHOOTING PROBLEM ACTION Check the fuse on the power socket. The projector doesn’t switch on Replace the lamp. The lamp comes on but the projector Make sure that the projector is correctly configurated. doesn’t respond to the controller Replace or repair the DMX cable. The projector only functions intermittently Make sure the fan is working and not dirty.
TECHNICAL DATA VOLTAGES: Electronical ballast(PR-2970): 100V/120V/200V/220V/230V/240V AC,50/60Hz Magnetic ballast(PR-2970M): 230V AC,50/60Hz Options: 200/220/240V AC,50/60Hz POWER CONSUMPTION: Electronical ballast(PR-2970): 1500W@220V Magnetic ballast(PR-2970M): 1600W@220V LAMP: PHILIPS MSR Gold 1200 SA/2 DE Colour Temperature 7500°K Socket SFc10-4,double ended Manufacturers Rated Lamp Life 750 Hours replacement...
Page 20
Energy saving function of the ballast Built-in analyzer for easy fault finding, error messages Built-in demo sequences Setup options by chargeable battery inside without power connection. Input signal isolating protection Network interface (Reserved) HOUSING: Composite plastic, IP20 WEIGHT: 35Kg Electronical ballast(PR-2970): Magnetic ballast(PR-2970M): 47Kg 20/26...
Need help?
Do you have a question about the PR-2970 and is the answer not in the manual?
Questions and answers