Baumfolder 714 Installation, Operation & Maintenance Manual

Baumfolder 714 Installation, Operation & Maintenance Manual

Friction feed folder

Advertisement

714 FRICTION FEED
MAINTENANCE & PARTS MANUAL
© Baumfolder Corp., 2003
© Baumfolder Corp., 2003
© Baumfolder Corp., 2003
© Baumfolder Corp., 2003
© Baumfolder Corp., 2003
FOLDER
INSTALLATION, OPERATION,
Printed in U.S.A.
Printed in U.S.A.
Printed in U.S.A.
Printed in U.S.A.
Printed in U.S.A.
PAGE 1
BAUMFOLDER
CORPORATION
Quality Bindery Equipment Since 1917
TP10449
TP10449
TP10449
TP10449
TP10449
TP10449

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 714 and is the answer not in the manual?

Questions and answers

Mahfuzul Haque
June 12, 2025

The weight of Buam 714B-2 airfeed folder machine without lower table?

User image 684ac12093ff5

Summary of Contents for Baumfolder 714

  • Page 1 BAUMFOLDER CORPORATION Quality Bindery Equipment Since 1917 714 FRICTION FEED FOLDER INSTALLATION, OPERATION, MAINTENANCE & PARTS MANUAL © Baumfolder Corp., 2003 © Baumfolder Corp., 2003 © Baumfolder Corp., 2003 © Baumfolder Corp., 2003 © Baumfolder Corp., 2003 Printed in U.S.A.
  • Page 2 • Be sure to replace any safety decals that may have been detached for any reason. BAUMFOLDER reserves the right to make changes in design or to make additions or improvements in its products without imposing any obligation upon itself to install them on its products previously manufactured.
  • Page 3: Table Of Contents

    Contents 1.0 INTRODUCTION ............................... 4 2.0 SPECIFICATIONS ..............................4 3.0 INSTALLATION ............................... 4 3.1 Unpacking & Inspection ............................. 4 4.0 ASSEMBLY ................................5 4.1 Main Unit ..................................5 4.2 Slitter Shaft Installation ..............................5 4.3 Delivery Table ................................5 4.4 Feed Table Assembly Installation ..........................5 4.5 Fold Plate Installation ..............................
  • Page 4: Introduction

    Your 714 Friction is a unique and versatile paper folding machine, capable of folding paper measuring between 3 x 5 inches (7.6 x 12.7 cm) and 14 x 20 inches (35.5 x 50.8 cm). The 714 Friction will make six types of folds: single fold, letter fold, fan fold, French fold, double-parallel fold and a double letter fold, with a few simple settings.
  • Page 5: Assembly

    WARNING Slitter Shaft Assembly Do not plug the power cord into an AC outlet until the 714 Friction is fully assembled, adjusted and ready to use. Unplug the 714 Friction any time disassembly is required. 4.0 ASSEMBLY 4.1 Main Unit To assemble the 714 Friction unit, first remove the four bolts holding it to the skid.
  • Page 6: Fold Plate Installation

    The first notch in the front part of the feed table #1 Fold Pan should rest on the pins. Then drop the rear notch down on the upper dowel pins. Rotate the handwheel to check that the gears are properly meshed. 4.5 Fold Plate Installation WARNING Unplug the AC power cord when installing or...
  • Page 7: Electrical Access

    6.1 Setting The Controls The operator controls are conveniently located on a 6.3 Paper Stop Adjustment control panel on the left-hand side of the 714 Friction. These controls consist of an On/Off power switch, which is an overload reset, and a speed control To move the paper stops to the correct position as potentiometer.
  • Page 8: Feed Table Adjustment

    Figure 6.2-1 6.4 Feed Table Adjustment Side Guide Locking Knobs On the paper feed table there are two guides which keep the stack of paper properly aligned for feeding into the folder. Adjust these guides to correspond with the different widths of paper being fed. (See Figure 6.4-1) To adjust the paper feed guides, loosen the two side guide locking knobs on each guide.
  • Page 9: Check Squareness Of Fold

    They are extremely sharp. TOP SHAFT 8.1 Perforating The 714 Friction can be used to perforate either the folded sheet (to assist in making a right-angle fold) or to perforate sheets delivered flat. BAUMFOLDER supplies one standard 41-tooth perforator blade. Additional perforator blades are available through the BAUMFOLDER Parts Department.
  • Page 10: Scoring

    TOP SHAFT 8.2 Scoring The 714 Friction can be used to score a sheet and deliver it flat, or to score a sheet after a fold or folds have been made. To ensure accuracy in making right-angle folds, always score the sheet where the fold is to be made. This applies in all instances when a perforator cannot be used.
  • Page 11: Maintenance

    543-6107. Space the rubber pull-out tires to support the sheet. Always be sure to give the model number and serial number of your 714 Friction to ensure receiving the proper parts. 9.0 MAINTENANCE 9.1 Maintenance and Care of your...
  • Page 12: Material Safety Data Sheet

    irritation and may affect central nervous system. May cause SUREWASH skin irritation. Chronic over-exposure to many petroleum 10.0 MATERIAL SAFETY DATA hydrocarbons may cause liver or kidney injury. May cause SHEET eye irritation. NOTICE: Surewash is a product of RBP Chemical Emergency &...

Table of Contents

Save PDF