Summagrid VII 2 Table of Contents Introduction Parts Checklist What You Will Need to Use Summagrid VII PC Requirements For a Serial Installation For a USB Installation Summagrid VII Overview Active Area Indicator Light Transducer Setup and Installation Overview Setting Up Your Summagrid VII...
Page 3
Did the software work in the past? Troubleshooting Chart Returning your Tablet for Repair Repacking for Shipment Parts and Accessories Glossary Regulatory Statements and Warranty Radio and Television Interference Canada Declaration of Conformity Japan Bescheinigung des Herstellers/Importeurs Limited Warranty for the Summagrid VII...
A digitizer is an electronic tablet work surface. The position of a transducer, a handheld cursor or stylus pen, on the work surface of Summagrid VII is converted – digitized – into data for computer processing. Data output from the Summagrid VII digitizer are in the form of an X/Y coordinate pair that pinpoints the precise location of the transducer on the tablet surface.
Summagrid is equipped with both an RS-232 serial interface and a USB interface. It is compatible with most industry-standard PCs. The TabletWorks CD contains drivers provided by GTCO CalComp by Turning Technologies and is the only software described in this manual. TabletWorks supports reduced functionality Wintab and TabCon-compatible applications.
Application software that accepts digitizer input via the Wintab API Overview The Summagrid VII digitizer consists of: Active Area The drawing area – the Active Area – is the portion of the tablet surface designated for digitizing. Its boundaries are marked at each corner by a right-angle crop mark.
(within the range) of the Active Area, the LED is solid green. Transducer Two types of transducers can be used with the Summagrid VII: pens and cursors. Both are available in corded and cordless versions. The corded transducers get their power from the digitizer.
Preparing the Summagrid VII Mounting on the Stand Place Summagrid VII on a table, desk or drafting table. You can also mount Summagrid VII on a stand or pedestal. The tablet’s Universal Mounting Brackets attach directly to those stands that have tilt arms. Stands with tilt pads require right-angle mounting brackets, which are attached to the tilt pads.
Software drivers provide the communication bridge between your digitizing software application and Summagrid VII. You should install only the drivers necessary for the Summagrid VII to work with your application software. If you are not sure which drivers are required, consult with your application vendor.
Summagrid VII 10 Hardware Configuration Summagrid VII must be configured so that it can send data in a way the application software will recognize and understand. Different applications have diverse requirements when interacting with a digitizer. Summagrid VII is designed to provide the appropriate serial requirements for a wide variety of graphic, CAD and estimating applications using the Tablet Configuration Utilities.
Summagrid VII 11 USB Connection The Summagrid VII USB port connection is USB 1.1 and 2.0 compatible. When the digitizer is connected to the USB port, Windows will recognize that there is a new device connected. If Windows displays the Found New Hardware prompt, follow the onscreen instructions to complete the driver installation.
USB installation, unless a high-accuracy cursor is being used. Tablet Power On The Summagrid VII power switch is located at the rear of the tablet on the Controller Connector Panel. When turned on, Summagrid VII’s Indicator Light will begin blinking.
Output Format Options GTCO: Selects GTCO-compatible formats. See Advanced Programing Information in the Summagrid VII Online Help for greater detail on GTCO format structure. Choices are: Binary high resolution, Binary low resolution, ASCII with spaces or ASCII without spaces.
Use the Tablet Configuration Utilities to configure the output format of the Summagrid VII. To Configure the Summagrid VII using the Tablet Configuration Utilities: 1. Make sure Summagrid VII is plugged into a Serial Port, powered on and all the tablet drivers have been uninstalled or disabled.
Page 15
Summagrid VII 15 5. Once the Summagrid VI has been found on a Serial Port, select Advanced Configuration from the Options dropdown list at the top of the screen. a. If Advanced Configuration is not an option, make sure Wintab Compatible Driver is not listed under Device Info.
The Tablet Configuration Utilities provide an easy, interactive way to set the tablet switches using the matrix in the upper right corner of the Summagrid VII Advanced Configuration screen. Locate each function setting required by your software application in the table below and check the switch or switches indicated to set that function.
Page 17
Summagrid VII 17 Select either the Save Temporary Settings or the Save Power-Up Settings option from the File menu after you have set all the functions.
Summagrid VII 18 Learning the Basics You will find that the Summagrid VII tablet is easier to use than a mouse. The Summagrid VII transducers are more accurate than a mouse, giving you greater control over your movements. Using the Transducer The transducer does not need to be in contact with the tablet surface in order for the tablet to sense its presence.
The lite touch pen is available only in the cordless version. It is similar to the click tip pen, except that it calls for, as the name implies, a lighter touch, without the click. Learning Basic Movements The Summagrid VII transducers provide all the basic movements of a mouse, including clicking, double-clicking and dragging. Clicking and Double-Clicking Clicking is the action of making a selection.
Summagrid VII 20 Cleaning the Cursor To clean the cursor body, use a mild cleanser. Do not spray the cleanser directly on the cursor – instead, dampen a soft cloth with a mixture of water and the cleanser. Clean the cursor reticles with alcohol.
Summagrid VII 21 Replacing the Cordless Pen Batteries The pen requires two 393 silver oxide batteries. The average battery life is 200 hours. To replace the batteries: 1. Unscrew the pen cap. Hold the pen from the bottom and gently slide off the pen cover to expose the batteries.
Summagrid VII 22 Replacing the Cordless Cursor Batteries The cordless cursor requires two AAA batteries. The average battery life for the cursor batteries is 2,000 hours. To replace the batteries: 1. Place the cursor face down in the palm of your hand. Use a Phillips...
Summagrid VII 23 Troubleshooting GTCO CalComp by Turning Technologies wants your experience with Summagrid VII to be a successful one. If you ever encounter a problem, please follow the steps below: 1. Reread this manual to verify you have performed the correct steps.
Summagrid VII 24 4. The cursor turns on again at the new frequency. You will know the cursor is on when the Indicator Light glows steadily. To return to the default frequency, repeat the above process. When you replace the cursor batteries, the cursor is automatically reset to the default frequency.
Summagrid VII 25 Computer Checklist Is the computer plugged into a live outlet? Did you turn on the computer? Does the computer work with any of your software? Try one of your other programs. If the computer has a diagnostic diskette, use it.
Summagrid VII 26 If you are using a PC, did the new software alter your AUTOEXEC.BAT file? Have you updated the software or its drivers? Are you loading another mouse driver? Did you reinstall the software, perhaps after a problem with your hard drive? ...
Because packing materials are static-charged, you should ship the cursor or any extra electronics boards inside approved antistatic plastic bags. If you are shipping the tablet or accessories to a GTCO CalComp by Turning Technologies Service Center for repair, attach a tag to the equipment with the following information: Model number ...
Summagrid VII 28 Parts and Accessories The following table lists the Summagrid VII systems and parts available for purchase. To order any of the items listed below, please contact GTCO CalComp by Turning Technologies at 1.866.746.3015 (Toll Free), fax to 480.998.1751, visit us online at www.gtcocalcomp.com, or email to gtco.sales@gtcocalcomp.com.
Summagrid VII 29 Glossary Accuracy The similarity of a distance measured by the tablet with the actual distance. When we specify that the accuracy of a tablet is ± .010 inches, we mean that every point in the Active Area is within .010 inches of where it should be.
Page 30
Summagrid VII 30 Data Rate Number of coordinate pairs (X,Y) the tablet sends to the computer per second. Default A value, action or setting that a computer system assumes, unless the user gives an explicit instruction to the contrary. Drawing Area Area on the tablet surface intended for digitizing.
Page 31
Summagrid VII 31 Line Mode The tablet sends coordinate data points continuously, while the pen tip or a cursor button is depressed, and one additional point when the pen tip or cursor button is released. Abbreviation for lines per inch. English unit of measurement for resolution measuring the number of separate, distinguishable locations that may be found within the distance of one inch.
Page 32
Summagrid VII 32 Proximity Greatest distance above the Active Area that the transducer can be raised and still be sensed by the tablet. Abbreviation for Random Access Memory, a specific type of memory used by the computer. Resolution Distance increment that the tablet outputs in lines/inch or lines/mm.
Summagrid VII 33 Regulatory Statements and Warranty Radio and Television Interference The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC rules.
Der Deutschen Bundespost wurde das Inverkehrbringen dieses Geraetes angezeigt und die Berechtigung zur Ueberpruefung der Serie auf Einhaltung der Bestimmungen eingeraumt. GTCO CalComp by Turning Technologies, Inc. (Name des Herstellers/Importeurs) Dieses Geraet wurde einzeln sowohl als auch in einer Anlage, die einen normalen Anwendungsfall nachbildet, auf die Einhaltung der Funkentstoerbestimmungen geprueft.
Page 36
Summagrid VII 36 Einhaltung mit betreffenden Bestimmungen kommt darauf an, dass geschirmte Ausfuhrungen gebraucht werden. Fuer die beschaffung richtiger Ausfuhrungen ist der Betrieber verantwirtlich.
Any damage in shipment of the product (claims must be presented to the carrier). d. Any other cause which does not relate to a manufacturing defect. 3. Any product not sold or leased to a consumer within six months of GTCO CALCOMP BY TURNING TECHNOLOGIES original sale date.
Page 38
Without a clearly marked RMA# on the shipping box, GTCO CalComp by Turning Technologies reserves the right to refuse the shipment. 3. Although you must pay any shipping charges to ship the product to GTCO CalComp by Turning Technologies for warranty service, GTCO CalComp by Turning Technologies will pay the return shipping charges for ground shipment.
Page 39
To obtain service on your GTCO CalComp by Turning Technologies product, call our Technical Support Department at: 1-866-746-3015 or fax us at (480) 998-1751. We can also be contacted through our website at www.gtcocalcomp.com...
Page 40
Turning Technologies assumes no responsibility for technical, or editorial errors, or omissions that may appear in this document, or for the use of this material. Nor does GTCO CalComp by Turning Technologies make any commitment to update the information contained in this document. This document contains proprietary information which is protected by copyright.
Need help?
Do you have a question about the Summagrid VII and is the answer not in the manual?
Questions and answers