Instrument Illumination Switch-To Remove; Fuel/Oil Level And Warning Lamp Switches-To Remove; Petrol Filler Door Switch-To Remove; Parking Lamp Switch/Heater Blower Switch-To Remove - Rolls-Royce Silver Shadow Workshop Manual

Rolls-Royce Silver Shadow 8 Bentley T Series
Workshop Manual
.
I)trscrr\v ant1 rcnlove the circular fresh air
~ ~ t t l c t
knob grub screws; remove the knobs
-1.
Remove the gear range selector cowl trim
fit~ishr,r
5
Remove the centre and left-hand or right-hand
facia panels.
6
[Jnscrew and remove the four screws securing
the picture plate and switch mounting plate.
7. Pull off the knob.
8.
Remove the switch securing nut and
shakeproof washer.
9. Disconnect the electrical connections, noting
the colours to facilitate assembly.
10. Remove the switch.
Windscreen wiperlwasher switch
-To remove
Proceed as for Radio balance control switch
-
To
remove, noting the following point.
1
Insert a thin probe into the underside of the
knob shank to release the tensioned retainer; pull
off the knob
Instrument illumination switch
-To remove
Proceed a s for Radio balance control switch
-
To
remove, noting the following point.
1. Insert a thin probe into the underside of the
knob shank to release the tensioned retainer; pull
off the knob
Air conditioning switches-To remove
1. Disconnect the battery.
2.
Carefully prise away from the centre console
with a flat tool the triangular trim pads situated one
on each side of the centre console
3.
Unscrew and remove the screws securing the
wooden facia panel to the console and slide the
facia until it clears the retaining clip at the base;
remove the facia.
4. Insert a thin probe into the underside of the
knob shank to release the tensioned retainer; pull
off the knobs.
5. Disconnect the electrical connections
6. Remove the four switch mounting plate screws
and washers.
7.
Carefully manoeuvre the switch out of the
console
Heating and demisting switches
-To remove
Proceed as f o ~ 4ir conditioning unit switches
-
TO
rcniobc.
Chapter
M
Fuelloil level and warning lamp
switches-To remove
1 Disbcmnect the battery
2
Remove the steering column cowl f~nisher.
3
Remove the switch button by pulling
rearwards.
4
Unscrew and remove the outer f a c ~ a panel
securing screws; remove the facia panel
5 Unscrew and remove the two switch mounting
plate retaining screws.
6.
Disconnect the electrical connections, noting
the colours to facilitate fitting
7
Remove the switch mounting plate by removing
the hexagon headed nut; remove the switch and
spacer
Petrol filler door switch-To remove
1. Disconnect the battery.
2
Remove the steering column cowl finisher.
3
Remove the outer facia panel.
4.
Remove the switchbox a s described in Section
M8
-
Instruments
5 . Unscrew and remove the switch circular
securing nut
6
Disconnect the electrical connections, noting
the colours to facilitate fitting.
7.
Remove the switch
Parking lamp switch-To remove
1. Disconnect the battery.
2. Using a suitably cranked probe, press in the
tensioned knob retainer, simultaneously pull off the
knob.
3. Unscrew and remove the two screws securing
the escutcheon; remove the escutcheon
4. Re.nove the handbrake handle trim panel.
5 Disconnect the electrical connections, noting
the colours to facilitate fitting
6 Remove the hexagon headed nut; remove the
switch.
Heater blower switch-To remove
1. Disconnect the battery
2.
Carefully prise away from the centre console
with a flat tool, the two triangular trim pads
situated one each side of the centre console.
3
Unscrew and remove the screws securir~g the
wooden facia to the console and slide the facia
until it clears the retaining clip at the base; remove
the facia
4. Disconnect the electrical connections, noting
the colours to facilitate fitting