Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Unitec 5 1115 0010-0020
Summary of Contents for Unitec 5 1115 0010-0020
- Page 1 M a s c h i n e n f a b r i k G m b H Pneumatic Metal Circular Saw Typ e 5 1115 0010-0020 Illustration can differ from the original Operation and Maintenance Manual CS Unitec, Inc.
-
Page 2: Technical Specification
90° ; 84 mm 45° ; 56 mm Noise level at 1 m distance 103.3 dB(A) Vibration level at free speed < 2.5 m/s² Avenue www.csunitec.com CS Unitec, Inc. Translation of the original manual, 511150010_20_BA_en_Version_00 Page 2 of 18 compiled: 24.02.11... - Page 3 6 Retracting blade guard 7 Adjustable rip fence 8 Sighting notch 9 Blade lock 10 Blade lock lock-off safety switch 11 Depth lock washer CS Unitec, Inc. Avenue www.csunitec.com Translation of the original manual, 511150010_20_BA_en_Version_00 Page 3 of 18 compiled: 24.02.11...
-
Page 4: Safety Instructions
They are for your protection. Wear goggles ( chips – risk of injury) Wear gloves (cutting damages by sharp edged work pieces) Wear safety shoes Wear protective clothing CS Unitec, Inc. Avenue www.csunitec.com Translation of the original manual, 511150010_20_BA_en_Version_00 Page 4 of 18... - Page 5 Always use blades with correct size and shape (round versus diamond) spindle holes. Blades that do not match the mounting hardware of the saw will run eccentrically. Causing loss of control. CS Unitec, Inc. Avenue www.csunitec.com Translation of the original manual,...
- Page 6 Position your body to either side of the blade, but not in line with the blade. Kickback could cause the saw to jump backwards, but the operator can control kickback forces, if proper precautions are taken. CS Unitec, Inc. Avenue www.csunitec.com...
-
Page 7: Additional Safety Instructions
An unprotected saw blade still running will move the saw towards the direction of sawing and saw anything standing in its path. Be aware of the time taken for the saw to run down. CS Unitec, Inc. Avenue www.csunitec.com... - Page 8 This machine is not applicable for cutting wood, masonry, magnesium or other pyrophorous material. Do not use cutting fluids or lubricants on the blade. CS Unitec, Inc. Avenue www.csunitec.com Translation of the original manual,...
- Page 9 Machine moves Tool blocks unknown unknown the tool Maintenance Operation at a Breakdown of the unknown unknown maintenance unit machine CS Unitec, Inc. Avenue www.csunitec.com Translation of the original manual, 511150010_20_BA_en_Version_00 Page 9 of 18 compiled: 24.02.11...
- Page 10 Only use original Tanitec saw blades. 6. Place the outer spindle flange on the spindle with the flat side towards the blade (see fig. 2) Abb. 2 Fig. 2 CS Unitec, Inc. Avenue www.csunitec.com Translation of the original manual, 511150010_20_BA_en_Version_00 Page 10 of 18 compiled: 24.02.11...
- Page 11 To adjust the depth of cut: 1. Disconnect tool from pneumatic supply. 2. Lift the depth lock lever at the rear of the saw (see fig. 4) Fig. 4 CS Unitec, Inc. Avenue www.csunitec.com Translation of the original manual, 511150010_20_BA_en_Version_00 Page 11 of 18 compiled: 24.02.11...
- Page 12 Align the cutting line on the work piece with the sighting notch. Make the cut. Use the right-hand notch (between the two marking dots) for straight cuts and the left- hand notch (located below the rivet) for 45- degree bevel cuts. CS Unitec, Inc. Avenue www.csunitec.com...
- Page 13 To replace the outer blade cover, line up tang with slot and push in against the spring while turning clockwise. Ensure that the cover is properly seated. CS Unitec, Inc. Avenue www.csunitec.com Translation of the original manual,...
- Page 14 Orient the line of cut. The required speed of the blade has to be achieved, before starting the cut. Wearing goggles, a dust mask and ear protection during use is compulsory. Do not use cutting fluids or lubricants on the blade. CS Unitec, Inc. Avenue www.csunitec.com...
- Page 15 The lubrication conditions and maintenance see „Maintenance of pneumatic tools“ CS Unitec, Inc. Avenue www.csunitec.com Translation of the original manual,...
- Page 16 M e t a l C i r c u l a r S a w P n e u m a t i c 5 1 1 1 5 0 0 1 0 - 0 0 2 0 CS Unitec, Inc. Avenue www.csunitec.com...
- Page 17 M e t a l C i r c u l a r S a w P n e u m a t i c 5 1 1 1 5 0 0 1 0 - 0 0 2 0 CS Unitec, Inc. Avenue www.csunitec.com...
-
Page 18: Troubleshooting
Description: Pneumatic Circular Saw Model 5 1115 0010-0020 complies with the provisions of the European Union Machine Directive 2006/42/ EC and conforms to the following standards or standardized documents: DIN EN ISO 12100 DIN 24063 DIN EN 60745-2-5 Name of the authorized person for documentation: Mr.
Need help?
Do you have a question about the 5 1115 0010-0020 and is the answer not in the manual?
Questions and answers